11047787800 Kenmore Washer - Instructions

Just went by instructions provided by parts web site

There are three screws in the back panel at the very top. I unscrewed them with a T25 driver tip and pulled the top panel off the machine, the water level pressure switch was located in the right rear corner of the washer. ( If you are facing the washer) I pulled off the hose and unplugged the old switch, popped the switch out, and snapped the new one in re-attached the plug and hose, put the top panel back on and the three screws back in! All in about fifteen minutes. My washer works like new.

I used the video at parts select as a review, then just followed it. Easy de-install, reminder there's water in the line be prepared with a pot or vase to hold the water. Easy install. Washer runs perfect now. As quiet as when we bought it. I always try to fix before I re-buy, not a big green guy but I try to keep stuff working and out of land fills. Also the part was at my door in 1 day, Awsome!.

After unplugging the washer, the unit was pulled forward and tipped backwards, I placed a 2x4 under the washer to serve as a brace. I removed the existing bolts holding the old pump in place, removed the spring hose clams, unplugged the pump and removed the damaged part. inserted the new drain pump, re-inserted the bolts and tightened them, replaced the spring clamps with "regular" hose clamps supplied with the replacement part, plugged in the power supply, removed the brace, pushed back the unit and plugged it into the outlet. From start to finish - about 20 minutes. Was running wash about a half hour after I started.

My dryer is on top my washer so I removed the dryer and pulled the washer out. I had to get rid of the water that was inside so I used my wet vacuum on the drain hose and sucked it out I then removed the front cover and the I tipped it back and removed two screws from the bottom of the pump bracket underneath the washer and moved the two clams on the pump hoses back to uncouple the hoses. I removed the pump and installed the new one and hocked everything back including the wires to the pump which is just a quick connect and pushed it back into place and it worked like new

It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money

First, I watched the video again just to make sure I had a firm grasp of the task ahead. I gathered up the tools and proceeded to begin. First obstacle: getting the washer tilted back enough to put the blocks under the front feet. The washer was sitting inside a square water pan with a drain connected directly under the middle of the washer. Therefore, the water pan did not move and I could only get the washer moved out far enough to 'barely' put the blocks underneath. Second obstacle: a clump of hair had gathered at the bottom portion of the door unnoticed and caused a slow leak from the bellows. This leak dripped down and rusted out two of the three screws. I had to use a socket set to get the screws out. Third obstacle: getting the pump removed from the bottom of the washer. With the drip, the pump had stuck to the bottom of the washer. Trying hard not to get cut on the sheet metal bottom, I pushed and pushed and pulled until finally the pump let loose. From that point on..smooth sailing just like the video. Washer fixed!

Followed video clip that I found online

I just put the divider in the dispencer

Remove the two screws holding the hinge to the washer body. Lift up on the hinge to remove from the washer. Remove all the screws holding the inner door piece to the outer cover. Remove the old hinge, replace with the new one. Put the two door pieces back together and tighten the screws. Place hinge back in on the washer body and push down. Replace screw at top and bottom. Close door and start using.

Remove top (held on with 3 screws on the back). Pressure switch is at the back right side. Remove rubber hose. Gently pry switch from side of machine. Remove electrical connection. Install electrical connection on new switch. Snap back into side of machine. Replace top. This was installed a couple of weeks ago and have not had either code since

Just use the video. Shows you all you need to know. Very easy. Do it yourself and it saves you money.

Removed top of washer and replaced flow meter.

Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You will need the screwdriver to tighten the screws in the inner clamp.

repair was a cake-walk with the video there to help.Thanx