JB670SP2SS General Electric Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,

We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!

Becuase of the fire we had used a chemical based fire extinguisher, which made a real mess in the whole main floor of the house. I removed the oven from the house and used a leaf blower to get rid of all the white chemical powder (like a baking soda of sorts). Once that issue was done, I removed the part in less than 5 minutes. Two screws to remove it and then unpluged the two wire clips from the back of the stove under the shield which also had 6 screws to remove. It took only 3 days to have a new one delivered and I installed it in less than 5 minutes. The oven works fine now. It took much longer to clean the house than fix the oven.

This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wires, put the screws back in place, replaced the cover, and the oven was as good as new.

removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.

First, pulled out the old heating element and all the peices that were left after it fell apart. Since when you pull out the old one, the wires it connects to tend to recess back into the oven wall, I had to pull out the oven and take the back cover off in order to push the wires and connectors back through the receptacle in the oven. This was really easy as you only have to remove 5 screws from the middle panel on the back of the oven rather than the entire oven back. Once the wires were back through, I just plugged in the new unit. The oven works just like new now. I'm sure I was able to save between $75 to $100 just for the service call by doing this myself.

Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success

My friend's husband came over to help. I mentioned that after unscrewing the old bake assembly unit, we would have to capture the wires or they would slip into the back. Before he even had the screws undone, the wires did, indeed, slip into the back. He then removed the back panel and retrieved the wires, pushed them back through the insulation and clipped each of them onto the back assembly. However, the wire clips kept slipping off so he eventually had to criimp the clips to keep them tight on the ends of the bake assembly. That troubled me; what if in the future one of those clips comes loose while the oven is in use? Any suggestions on how to keep these connectors on tightly?

Pulled out stove. Removed rear panel, and set aside. Removed melted bake element by unscrewing the mounting plate screws, and unplugging both leads from the stove. Replaced in reverese fashion. Easiest electrical replacement I have done.

I unscrewed the 2 screws that held in the element, pulled it out a little, disconnected the 2 wires, got the new element out of the box, connected the two wires on the new element, put the screws back in and it was done! Very easy.

After reading about possible losses of the wire leads, I put together a simple solution. First, turned off the breaker, then pulled the grates out for full access.
Using a nutdriver on the hex-head screws holding the backing plate to the oven wall, I removed the screws, then gently lifted and pulled the element and it's attached wire leads out of the insulated rear of the oven.
Attach a plastic clothespin to each lead above the spring clip attaching the lead to the element so the springy wire would not tend to pull back into the difficult-to-access insulated area "behind the wall" because that would be a real pain to get at.
With nothing other than fingers, the spring clips can then be removed from the tabs on the element, the old piece removed, the new element set in place and quickly re-connected. No Problem!

First, my husband removed the two screws that hold in the element. Unfortunately, my GE Spectra oven had extremely short wires. That was the only thing that made it somewhat difficult. So, he pulled the element out as far as he safely could, replaced it with the new one. No problem! As I said, the only thing that made it difficult was the short wires supplied by GE. The part came from PartSelect.com with no problems. I would definitely use this website again to order parts.

First I unplugged the stove. Then I removed the two screws inside the oven to remove the heating element. For safety purposes I removed the back panel from the stove also to get a complete view of what I was getting into. That was just 5 more screws and the panel came off and exposed what the heating element was plugged into. Very easy to unplug and reconnect, install the back panel then install the two screws for the heating element and it works just fine.

I went online, found what I thought was the correct part, ordered it, received it--WRONG ELEMENT!
HUBBY phoned parts company, very nice gal helped him find correct element, put new one in the mail to us, and we mailed back the wrong one. We received confirmation via email, and 3 days later installed the proper element. I am back to baking. I bake & mail cookies (55,000 to date) to our deployed troops, so I was lost without my oven! Thanks People!

First unplug the unit from the outlet. Then remove the rear cover, covering the electrical wires. Disconnect the hot /ground wires from the element leads. Then open the oven door and use the nut driver to remove the inner screws to release the bake element. Insert new element and replace all screws and electrical leads. You're all done!