GS2327EADW Maytag Refrigerator - Instructions

I read what other people had done so I tried the easiest solution--Forced, without breaking, the plastic & fit the ring right where it needed to be.

Removed 2 screws from front panel. disconnected the connector from the front panel board and removed front panel. Removed 3 screws holding dispenser to inside door. Pulled this assembly forward to reach the cover and switch. removed 1 screw holding switch. replaced the actuator ( a matter of hooking the slots of the pad over the ears. Reversed proceedure to reassemble. No problems at all

Poped ou the old switch, connected new switch and pushed back into socket.

replaced the broken basket stop with new one. took a whole minute to do so!!!!!

This was easy. Removed the plastic cover at the top hinge. Removed the 3 screws at the top hinge. Lifted the door off of the bottom hinge and laid it on it's side. The part that was worn out is the "natural door closer". It looks like this part will need to be replaced every few years, it is made of plastic and was ground down to nubs. Remove the screws holding it down and replace it with the new one. Lubed it up with some WD40 to get rid of squeaks. I also replaced the lower hinge pin, but I don't think that was necessary.

Removed the top hinge of the door. Lift door off the lower hinge. Unscrewed the "natural closer" from the bottom of the door and replaced with new part. Pulled off the lower hinge from the lower bracket and replaced with new hinge pin. Replaced and realigned door. Piece of cake!

have always done it myself, but Maytag store closed, so I didn't know where to purchase filter

I received it from Parts Select, in 2 days and if I remember right, price was cheaper than I paid last year, at store.

Place two 2x4s, stacked on each other on floor parallel and close to refrigerator, leaving room for socket handle and extensions to three lower hinge bolts. Placed 3 foot 2x4 at right angles on top of the parallel stack of 2x4s, with one end under right hand refrigerator door. Placed 20-30 lb bucket of rice on other end of 2x4 to exert upward pressure on door, raising door bottom off of hinge pin. Removed three hinge screws. Replaced Natural Door Closer and Lower Hinge pin. Screwed three hinge pin screws back in. Removed fulcrum.

The most time-consuming part was removing the screws. First, remove the 8 screws that attaches the ice bin to the front cover. This will free up the auger enough to pull up the back end where the drive ring is held in place. The ring just pops right out. The only thing I recommend is as long as you have the bin out (and empty), go ahead and give it a good wash. Make sure it is thoroughly dry so that no ice freezes to the moving parts.

I simply removed the old brackets and replaced with the new ones. Can't get any easier than that!

My husband did the replacement of the filter, so it was really easy for me. Easy for him too! The best part was this company had the best price, and the part was here in no time!

it was a cake walk,removed a few screws unpluged assembly installed new switch didnt get shocked, nothing started on fire, ice came out like it should afterwards

Removed the face plate by removing the two screws under the fountain catch tray on the front of the fridge, and then sliding the cover up and off. Removed 3 screws to remove the dispenser and the limit switch was easily accessible on the back side. Also changed the actuator pad because the old one looked cosmetically bad.

First, I removed the water/ice fountain panel - remove the 4 screws and disconnect the panel buttons cable. Second, I removed the panel circuit board - remove the two screws and disconnect the two wire connectors. Third, I pulled the water/ice fountain compartment. Removed the broken rubber pad (actuator pad), and installed the new one -- no tools needed for this step. Finally, I put everything back together. TIP: If the water/ice switch gets stuck, even with the new actuator, find a spring that can fit the switch pin that comes with the actuator. I had that problem, and I simply added a small spring.)

Replaced actuator pad