Models > 79090820407 > Instructions

79090820407 Kenmore Range - Instructions

All Instructions for the 79090820407
91 - 105 of 522
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lower Heat element burned out.
1.Take no chances. Turn off power at main breaker box (Range). 2 2. 2. 2.Remove inside grills then pull damaged element forward to expose wires and screws. 3. Use nut driver or phillips screwdriver to undo both screws. 4. Remove burnt out element then replace it new one. Make sure both sides are firmly pushed onto the wire terminals before tightening screws. Replace grills. close oven door then turn breaker at breaker box on again.
Parts Used:
Oven Bake Element
  • Horace from CRUMPLER, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove Element Stopped Working
Unpluged Oven, Removed 2 screws, unpluged Element, Plugged in new element. Replaced 2 screws, plugged oven in. Done 15 minutes.
Parts Used:
Oven Bake Element
  • Daniel from CASTALIA, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out bottom oven element
Undid 2 screw nuts holding the element to the back wall, with a 1/4" socket. Pulled off the two wires, pushed them onto the new element. Screwed the two nuts back on the rear wall. Done! Easy, worked 1st try.
Parts Used:
Oven Bake Element
  • Scott from ALBANY, OR
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had no control on Big burner
Replaced the switch very easily! Working great
Parts Used:
Oven Bake Element Infinite Burner Switch
  • JAVAD from KNOXVILLE, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No oven heat, but the broiler worked fine. All top burners worked.
Removed the oven heater and checked with an ohm meter. It read 'open', so I ordered a new element. It came in a few days, and my 16 year old grandson installed it, and all is well!
Parts Used:
Oven Bake Element
  • George from WESTMINSTER, MD
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bake Element replaced
Watch the easy install video a couple of times and easy as a piece of cake!
Parts Used:
Oven Bake Element
  • Roxanne from CANTON, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burned element !
replaced the element !
Parts Used:
Oven Bake Element
  • BILLY from JACKSON, MS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would only get slightly warm.
Loosen 2 screw with a 1/4 nut driver. Pulled element out to expose connections. Carefully disconnected old element and replaced with new element. Pushed wires back into holes and replaced the screws. (Note: Be careful not to let the disconnected wires slip back through the holes. This almost happen to me)
Parts Used:
Oven Bake Element
  • James from INDIANAPOLIS, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
8" burners were not responding correctly to the switches
Pull range away from the wall. Unplug range. Remove back plate covering the switches. Remove defective switch. Use bent paper clip to press center of terminal connectors and disconnect terminals. Reconnect each terminal of new switch as you go to avoid confusing terminals and connectors. Re-attach switch. Plug in range and test elements. Clean range area. Push range back into place, being sure to engage the anti-tip safety device.
Parts Used:
Infinite Burner Switch
  • Carl from W SAND LAKE, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven element broke
Since I had the element out I cleaned the stove. That took me 2.5 hours. Used cold spray and let sit for two hours and wipe out clean took about 30 minutes. Now for the element itself it took me about five minutes to put the new one in. Oven looks and works like new. Just google your repair needed and watch the video. Easy Peasy. Last time I had it done by an electoral repair person for the tune of about $100.00. This time I bought the part and did it my self. Cost less than $25.00 including tax and shipping. No brainer.
Parts Used:
Oven Bake Element
  • DAVID from PEACHTREE CTY, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner was inconsistent the heating with red hot one minute and not the next minute
I watched the video on how to do it
Parts Used:
Infinite Burner Switch
  • Richard from Florence, OR
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element in oven burned through
Turned off circuit breaker to the oven, unscrew the 2 small screws, pulled the element away from the back, pull element away from the wires in the oven and replace with the new one and replace the screws. Tirn circuit breaker back on
Parts Used:
Oven Bake Element
  • Jean from MARIETTA, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom oven element was burnt out
Unscrewed 2 screws, used pliers to pull off push on terminals attached to element . Slide terminals back onto new element and replaced screws. EASY
Parts Used:
Oven Bake Element
  • Sherry from JAMES STORE, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Our old element super heated in one corner and broke.
There are two philips head screws in the back wall of the oven to pull. Gently slide the element forward with the attached wires. Pull the terminals off of each side of the element, slide on to new element, push into place, and replace screws. The whole job was done in under 3 minutes.
Parts Used:
Oven Bake Element
  • David from MOUNT VERNON, ME
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bake element burnt out and snapped and appeared to try to arc-weld itself back together?!!
Just followed the very simple video instructions…it took less than 5 minutes.
Parts Used:
Oven Bake Element
  • Albert from STUART, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 79090820407
91 - 105 of 522
Back to Top