All Installation Instructions for Whirlpool Refrigerator 6EC3FHKXWQ00

the track holding the snack compartment broke

watched the video provided on this site. I thought I would have to buy the whole glass panel and then the video showed how the tacks pop off and how easy it was to put the new ones on. So glad to have found this site. I will check here whenever I need a part. Also, the item arrived in 2 days!

Parts Used:

Pan Slide Track

candice from monrovia, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Slide was broke.

Took off old one. Put on new one. Put drawer back into refrigerator.

Parts Used:

Pan Slide Track

Phyllis from Harcourt, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Meat drawer plastic slide bar broke

Pull meat drawer out of fridge. take off shelf bracket, remove broken slide guard, replace with new slide.

Parts Used:

Pan Slide Track

Jill from St. George, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Connector tabs on new slide track were too tight to push into position

Approached the repair as described in the video. Removal went very well. On installation the plastic tabs on the slide track were too tight to push into lock position using only hands. Had to use a screw driver and small hammer to tap the slide track into locked position. I regret that I did not replace both tracks at the same time.

Parts Used:

Pan Slide Track

Alton from Wetumpka, AL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Pan Slide Tracks Were Broken

I ordered the parts and recieved them in about 4 days. I was very pleased with the time between order and delivery. I watched the installation demo provided and it was as spot on. All I needed was a small hammer to tap the old slide loose and the new slide on.

Parts Used:

Pan Slide Track

Raymond from Plain, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Replace broken hydator drawer slide

Remove old slide (broken part ). Tap in new slide with small hammer or kitchen knife handle.

Parts Used:

Pan Slide Track

Gregory from Marietta, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Replaced a missing part

Inherited this fridge from a sibling, but was missing a track so I couldn't use one drawer. Researched online and found the part from Partselect, and the track arrived literally the next day. Perfect fit, and now I can use the drawer. Made the wife happy.

Parts Used:

Pan Slide Track

John from Fremont, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

pan side track cracked

took the shelf out. slid both old side tracks out. new parts had two small plastic nipples on the end of the track that I had to remove. Then the part slid in and it is good as new. Thank You

Parts Used:

Pan Slide Track

John from Toms River, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Thank you for voting!

broken track for drawer

Removed the old slid in the new!

Parts Used:

Cantilever Shelf with Glass

Glenda from Ctrowley, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Pan side track cracked

Pulled the shelf out and replaced the slide rails. I watched the how to video on your website and it was very accurate and easy! Took longer to empty the drawer than it did to make the repair. Easy to do!

Parts Used:

Pan Slide Track

Thomas from Savannah, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

cracked fridge drawer slide

Nail set was used to push a locking bump to free the old slide. New slide had large bumps on each end which didn't allow tabs to engage mounting.slots on holder. File was used to reduce size of bumps. Original slide had a single bump in the center which fit intro a hole allowing the slide to lock in place securely.

Parts Used:

Pan Slide Track

Donald from Tucson, AZ
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Thank you for voting!

Pan slide track tolerance too tight

The slide track is designed to slide directly into the slotted metal rails in a no tools required application. However, the tabs in the plastic slide track were slightly bowed inward which decreased the tolerance required to slide freely. After several attempts the plastic then became slightly gouged by the metal rail further preventing the slide track from sliding all the way into place and into the detent. I ended up using a small file to file down the plastic slide track just a bit to remove the gouged plastic and create the required tolerance to allow the slide track to slide into its intended position.

Parts Used:

Pan Slide Track

Trent from Otsego, MI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Broken slides for the drawer in the refrigerator

I got the part in 1 day. I ordered at 1pm and got it at 11am the next morning. I used the wooden handle from a screwdriver and a hammer to tap the slides loose. The new ones went on easily. It took me longer to get everything off the support shelf and back in afterwards then it did to do the job. Actually doing the job took 5 minutes.

Parts Used:

Pan Slide Track