59670003000 Kenmore Refrigerator - Instructions

Removed old water inlet valve and replaced same with the new one. Installation was easy, parts came quickly, and I now have ice cubes again. Thanks for your help.

I used the process of elimination. The freezer was cold but the fridge side was warm. The motor was runing but the fan was not working. I unplugged the power cord and pulled everything out of the freezer. Then I took the coil cover out. The unit was frozen solid. I used my wifes hair dryer to melt the ice on the coil and spray water with a bottle to speed up the process. It took about 15 minutes to melt the ice and plug the power cord again. The motor kicked on and the fan started blowing right away so I know it's not the fan. The following morning it was frozen again. I repeated the process of taking everything out and tested the heater element with a multimeter. It wasn't working allowing the ice to build over the coil so I replaced it. It took about 30 minutes to replace but two days later it froze again. I read a little to learn about the timer and the thermostat function in a refrigerator. The timer rotates to turn off the motor and turn on the heater element to melt the ice on the coil. I tried to rotate it but it felt too hard to turn and it smelled burnt out so I replaced it at once. It took me less than 10 minutes to replace. I also learn that the thermostat reaches certain temperature and activates the fan which blows the cold air out of the coil and throughout the fridge compartments. Because the coil and the thermostat were getting covered in ice, it was not activating the fan to blow the air out keeping the freezer side cold and the fridge side warm. By replacing them both, the thermostat and the timer I solved the problem. It took about 30 minutes to replace the thermostat but now it's working like a brand new one again.

took all the pieces off- slid the new one into place. POOF!

Turn off water supply. Unplug the refridgerator and move so easy access to back. Remember to lower front right wheel to lift rubber foot off ground. Locate valve and remove, note color orientation of wiring (I did not have to remove cardboard cover.) Have a bucket and towel handy because water will spill. Compare the valves to ensure correct part. Apply teflon tape to threads and reconnect hoses and turn on water supply to check for leaks. Then connect power supply and re-attach to refridgerator. Use vac to clean back of refridgerator of dust and build up. Move refridgerator into position and raise front right wheel until rubber foot is back on floor. Use vac to clean coils in the front of the refridgerator. Replace grill. I allowed 4 batches to run before using ice. Pretty simple repair.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

This was an easy fix. The first thing you need to do is shut off the water to the ice maker. Then unplug refrigerator. Then take the panels off the back of the refrigerator to get to the water valve. The valve is at the bottom left hand corner. Take the inlet hose off and the outer hose off of the valve. Take the screws out to remove the valve from the panel. Replace the valve with the new one and hook up the hoses again. Make sure to tighten securely so that you do not have any leaks. Put everything back together and plug refrigerator in. Turn on water slowly and check for leaks. If no leaks, push refrigerator back and wait for the ice to begin. Piece of cake!!

Removed and Replaced

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

This is the easiest repair to perform, figuring out what was wrong took a little longer. I have the bottom freezer Amana refrigerator and the defrost timer is just behind the bottom front grill, removing four screws and plugging in the new timer took maybe 15 minutes. To find out what was not working correctly I removed the panel covering the coils in the freezer and it was totally frozen up, this is why it stopped making ice and wasn't keeping things cold. I defrosted the coils and checked the resistance of the heater to make sure it was working, it was fine so it was the defrost timer.

The repair was relatively simple.
The hard part was diagnosing the problem. Two of the sheet metal screws were hard to get at.
The online support helped in isolating and fixing the problem. The frig works fine again.