22308 ((1988)) Kenmore Range - Instructions

Pulled out the old one, pluged in the new one. It took me longer to open the box! PartSelect made it so easy to order and the shipping was super fast and at low cost. I looked on ebay and saw people paying more (with shipping and handling) for used parts. Thank you PartSelect!

just plugged it into the unit

Took out of box and plugged into slot.....even I was capable of doing this....easy

My old burners pluged in. I pulled out the old burners unpacked the the new burners pluged them in. I turned on the new burners and tested themand they worked!!

Simple replace-new for old

First I removed the two screws that hold the chrome piece that had the switch in it. I had to disconnect the two lights that light up when the elements go on, had to do that to get to the lock washers that hold the switch in place. Put the new switch in place but couldnt get the new lock washers on the both broke, had to go to the hardware store and get new ones just as little bit bigger, they went on slick. The switch works great again, buy new lock washers before you start

Removed grill cover, two phillip screws on front end of the vent holding the switch assembly in place. Lifted the switch assembly and removed the two wires (plugged into lugs). Then removed the two universal nuts with a 3/8" nutdriver and removed the old switch. Cleaned area and put the new switch in place and replaced the universal nuts, then attached the wires. Replaced the switch assembly and the two holding screws. Then inserted the grill cover and Voila! Finished

Pulled out old cartridges and installed new. Very easy and they work perfectly.
I was very happy with the extremely timely receipt of my purchase which was overnight. I paid for standard 3-5 day delivery.
This was a wonderful experience and I thank you again for your help.

You probably want to look inside as you read this. Most of it is straightforward, except the retaining clips.

First, I turned off the breaker switch. Opening the control housing, I disconnected the two leads and wrote down their orientation (one is silver, the other copper). In my JennAir model, an orange burner light is on either side of the fan switch. The white plastic on the rear is held on by their keyhole shape - just slide them the only way they can. This gives extra working room.

Since the switch plastic was already decayed, I snapped off the whole central square unit leaving the 2 portions held onto the posts by the metal retaining clips. Using a small flathead screwdriver, I pried up the plastic remnants, working around it until the retaining clips came loose/ broke.

The new unit fit perfectly and easily. The new retaining clips needed to be worked down a small circular file to spread the centers out enough for me to work onto the retaining posts. The file was just barely bigger than the existing hole. The clips can be broken if you are too rough or work them too much. After that, I used a pair of snub nosed pliers to push the clips down the posts. They required a considerable amount of force, but they aren't going anywhere anytime soon.

Reconnect the lights, reconnect the 2 leads, and check for any loose wires from other controls and loose parts. Reseat the control housing, turn on the breaker and test.

Lifted the grill out and slid the new burner unit in place. This was very easy; no problem at all.

I think Part Select is great, but my story? I just plugged in a module.

It was so easy...well...a technical writer--one of those people who writes operation manuals--could have done it. But afterward, they wouldn't have been able to explain to anyone other than another tech writer how it was done.

Just unplugged the old cartridge and plugged in the new one. It took 2 seconds.

Installation was straight forward as the new vent cap was sized correctly for exhaust pipe (5 inch). Placed the mounting plate into the exhaust pipe and used 4 SS screws to anchor to house sheathing. The vent flapper was not flat, requiring that I carefully stress relieve it at 250 degrees and hold it flat while cooling to take warp out. Snapped it in place afterwards and then bolted on cover.

I first thought it was the switch. I ordered one and the wrong one was shipped to me FROM ANOTHER COMPANY. After more trouble shooting I discovered it was the cartridge that needed to be replaces. I ordered one and again, the wrong one was shipped to me. They told me I could not get the right part because they were not made anymore.

So, I shipped it back and got in touch with Part Select. They found the right part and shipped it to me in 2 days. Problem fixed with the EXACT right part. I ordered the first part more than two months prior to receiving the correct part from PartSelect. All I had to do was plug it in to the recepticle in the stove. No tools required.

I feel that the design of the indicator light, with the base attached to the bottom of the lens, is ingenious in that it eliminates the need for fasteners in that confined space, However, the plastic used for the base needs to be more flexible. Part of the base broke off in trying to force the base over the bottom of the lens. Fortunately, there was enough left on the base that I could slip it over the bottom of the lens and complete the installation.