11084090410 Kenmore Washer - Instructions

Rmoved top, removed back, replaced valve.

I own a small, local handyman service as a Father/Son team. This repair is PERFECT for an apprentice to do as a confidence biulder. He learned the safe way to service a machine with garanteed success. This is a job anyone with basic knowledge can easily do with a little on-line homework on their machine. -Jim & Tom W.-

This was a thirty year old Kenmore washer. I removed the control frame, and then removed the two nuts holding the water inlet valve. The valve itself was easy, two water lines and one fill line. Reassembly was problematic as this valve was not exactly the same, I just tied off the valve to the water lines so it would not move.
Of course what took the most time was a run to Home Depot as the hot and cold water hoses were old and I replaced them with new.

Followed the instructions on the Part Select video which were very clear. I removed control module from top of washer, pulled the washing machine outer housing forward slightly and disengaged the rear closure panel slightly. I disconnected the electrical harness and then I was then able to remove the existing inlet valve. The new valve was then installed and the precess reversed to complete the installation.

Piece of cake!! (The water comes pouring into the machine now)

looked on the find a part by s symptom. found the part,moved the washer took off the back.took 2 screws off of the top of the machine/controls.lifted the top.replace the water inlet valve.put it back together.easy repair.

Removed backing and hoses and replaced the water inlet valve.

followed the video i found on Parts Select. Most difficult part was getting the frame back on correctly. Everything else was a breeze. Works great now.

I replaced the water inlet valve. First I watched a YouTube video on the repair; surprised to learn that you take the machine apart from the front, not the back.A few tips; pull the washer all the way out first; have extra tools in case you have the same problem as I did that the flathead screws holding the old valve on the back were too tight and had a shallow slot; it took several wrenches and pliers to get them turning. Do NOT forget to hook the internal hose back to the valve before reassembling the machine;and pay close attention to how the housing of the washer fits onto the frame, so that you can more easily put it back together. It would be helpful to have a second person for that step. All said, it was pretty easy to replace the part and I probably saved $200 and didn't have to sit around for a repairman.

I followed the great step by step video instructions that you provided. The only difficulty was getting the plugs off the Water Inlet Valve. I had to use pliers (gently) to pull the two plugs off. I would highly recommend PartSelect to my friends.

I watched the video on changing the valve. Then ordered the part. The video showed exactly how to do the repair and it was so easy.

Had no problem in disassembling the unit to get to the water inlet valve area. Very little problem installling the inlet valve but had somewhat of a difficult time getting the housing reassembled. There is a good flow of both hot and cold water which has cut down on the fill up time and washing time. Glad it is still working after 15 years. Instructions on the internet were extremely helpful. The delivery time of part was amazingly fast.

I notice a screetching sound started and as time went on the water that flowed out to fill water drum was not working properly, unplugged washing machine electrical cord from outlet. disconnected water hoses, removed screws from control panel, pulled out front cover off wachine machine to access water valve, removed by unscrewing 2 screws, placed bracket on new part(placed over valve and pushed bracket up to slide and align srew to tightenbracket), put everything back in reverse order, helpfull video on video web site for visual

I replaces the water inlet valve and now I have full pressure for the cold water to fill the tub.

replaced valve. Everything now working. Ordering the part was simple and I found a how to video on line that was great The whole replacement of the defective part was easy and the machine was back on line in 30 minutes.

Our washer's cold water flow became very slow. We were living with just hot water washing for about a month. I had used PartSelect in past and have always been very satisfied with the outcome. So, I went on the site and within a couple of minutes of navigating, had the part (water inlet valve with mounting plate) on order.

I watched the repair video on the water valve ordering page. My installation went pretty much to this procedure, with one exception, I had to use the mounting plate, which I don't think was covered in the video. You have to read and follow the instruction sheet that comes with the part. Therefore, my installation instructions are to a) watch the video, b) get together all the recommended tools described in the video, c) be prepared to use the mounting plate (which uses the same 1/4 nutdriver the video says is needed).

I did the complete valve replacement and had the washer back in place in just at 30 minutes, the tight closet quarters added a bit to this time I'm sure. Working in a basement or open utility room would have been a little easier and quicker. My shortfall though is, I should have done the hose connection check (turning the supply valves back on) before making the move back into the washer space, as once I performed what I thought was my last step, turning on the supply valves, I heard a water leak. This was resolved with another 10 minutes worth of moving the washer back out, disconnecting the hose, removing the rust debris which apparently caused the leak, reconnecting the hose, and this time, checking for leaks BEFORE moving the appliance back into place. I think the time estimate of 30 minutes is good for individuals with moderate experience in appliance repair, and probably good for the novice in conjunction with the video.