11081422510 Kenmore Washer Dryer Combo - Instructions

I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.

The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.

very easy to repair , instructions very clear , parts person very good to talk to, parts got here fast

part fit perfect

I just unscrewed the top agitator cap and slid the o-ring on and put it back. Done in seconds.

Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!

Pulled the old one out, took the duck tape off (haha) and snapped, pushed the new one on. Piece of cake. I then noticed that this is a movable door ,and ther was the same part on the other side, oh well now I still have a spair.

Turned off power and pulled power plug from the wall. Removed the two screws at the lint screen. Raised the top to by depressing the top spring clips. Removed the two 5/16" screws from front top. Removed wiring clips from front panel. Set the front aside while I removed the two broken panel clips. Installed the two new panel clips. reinstalled the front panel by placing the front panel above the sides. Opened the front panel door and supported the drum while allowing the front panel to slide down onto the new front panel clips. Reinstalled the wiring clip. reinstalled the two 5/16 screws. Turned the drum to ensure that the felt seals and drive belt weere installed properly. Lowered the top and reinstalled the two screws at lint screen. Reinstalled power plug and turned on power. No rattles or squeeks!!!

1) removed three screws on the top back 2) removed top 3) removed two screws holding the front on 4) pulled front up and it came off 5) cleaned out dryer 6) put belt back on according to a video on Youtube 7) put it back together and my 35 year old dryer is as good as new

Push new catch in the opening, close the door and VOILA! the door stays closed. Please note that the cost of this part is exorbitant- it's worth about 50 cents but with shipping it cost about $11.00. Check your local hardware store first.

After ordering the part, I read the information left by other users. I used a screw driver to pop out the piece, and then put the new latch in the opening. A gentle pop with the side of my hand, and the door latch went right into place. Who knew there was a second door latch on the other side that could've been used?

Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!

Removed the control panel and the cabanit. Then removed the adjutatior . Removed the motor and gear box slid the old shaft out and put the new one in put back together. Took about one hour .

I pulled out the old cap with my hands and jammed the new thingy into place. The lady of house did the repair. Easy

Not knowing exactly what needed to be replaced I used the in-site questionnaire and followed through to problem and then ordered the first two items suggestions. Turned out the Heating Element Connection Wire Kit was redundant and not needed as the Cycling Thermostat included two such wire kits. I watched the video on the site and that gave me a fairly good idea how to proceed. I removed the back panel, lot of small screws, and then the Thermostat was easy to see. There are two similar looking parts but after closer look only one matched the new thermostat. Super easy, just remove wires and old thermostat and replace with new item and then before actually reinstalling back panel I put a load of damp clothes to dry. Half hour later...Wallaaa...problem resolved. Good luck with your fix. Oh, there is a sheet referencing to set the new thermostat if needed to a certain limit, however using old thermostat with its embedded model # found that factory setting for new one was fine. So, no need to reset.