11081422510 Kenmore Washer Dryer Combo - Instructions

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

I took out the old worn out part and replaced with the one I order.

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

From the front, taped part in place and then assembled springs and insulator from the rear. Difficulty occurred with access to the back of the sensor due to the air duct interference. The sharp edges of the sheet metal parts increases the risk of cuts. First shipment was missing the second electrode but Part Select immediately replaced the shipment. My experience has to be considered Excellent and I would go to Part Select first for my next order.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

Removed broken hose and replaced with new hose. My washer will be 21 years old in January.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I replaced a bad thermostat

slipped new rear leveling legs into leveling fixture. Fit even though it wasn't specified to be the right part for this old washer.

New hose was perfect, went on easy.

1. Need mop, bucket to catch leftover water in machine before you remove old hose. 2. Removed old hose by removing clamp. 3. Dried up any remaining water around fixture before attaching new hose. 4. Slide clamp to bottom of hose before attaching to machine. 5. Attached hose and clamp to machine where old hose was removed from. Make sure clamp is secure. (Please note that clamp that came with the new hose was too big. I used the old one. Worked perfectly). 6. Finally run a little water in you washer, then run out to test tightness and there is no leaks.

(For those who have a weird sunken plastic cube slot instead of a nut or screw to remove) The dog teeth were worn down. Generally this is an easy repair. It happened once before to me with a Whirlpool and I knew immediately what I needed to do. HOWEVER, when I popped the plastic cap off the top of the agitator (this model doesn't have the fab softener dispenser) what I found was a surprise. It wasn't an 11mm nut, it wasn't a screw, it was an inverted cubed slot made of plastic (not sure what those are called) that looked like it needed a 3/4 - 1 inch socket drive to go into it. I had nothing that would fit in there to get any leverage to loosen it up. Frustrated, I began grabbing everything I could find to shove in there that I thought might grab to no avail. In pure desperation I grabbed my wife's garden shears (the common little hand-held kind that curve at the end) and it was the perfect size to wedge in just enough to grab the corners of the cubed-shape slot. It took just a little force to loosen and I was able to unscrew it by hand after that. Then the repair was just as it normally is. Remove the top piece of the agitator, remove the spring piece and slip the plastic part up to remove the dog teeth. Replace, put back together in reverse order.

Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!