R200 Jenn-Air Cooktop - Instructions

Turn off elec. power at breaker box. Check twice. Removed burner switch cover. caarefull remove wires from switch, note with color to which terminal remove nut on switch replace new switch replace wires to switch, replace cover turn on power. ready.

Removed old knobs and installed new. No tools were required.

Replaced the element. The part came the next day which was great. Good customer service!

First I disconnect the breaker. I removed the defected receptacle and cut the wires. I connected the new receptacle with parts with the new part. Turned the breaker back on and everthing worked fine.

Fed-Ex delivered the package and within 10 min I had open the package, removed the old knobs and installed the new ones, My wife was very impressed with the ease of the transactionl. It is good to know that we can still get parts for our cook top even though it is 26 years old. Thanks for every thing.

I removed the burner elements for three burners by lifting the surface top and unplugging them. I snapped out the plug sockets that were burned out and cut the two wires, one element at a time. Using the included wire nuts I stripped the ends of the cut wire and connected each wire to one of the wires on the new socket. Once the wires were connected I snapped the sockets in place and reinstalled the elements, lowered the surface top and the range was ready to use.

After buying a 'universal' part at Lowe's and it not fitting correctly and shorting out the burner, I went online and found this source for an exact replacement part. Beside having to disassemble the drop in stove burner two or three times it went well when I had the correct part. I lost one screw somewhere and that delayed me a short time to find a replacement. Thus the 1 to 2 hours. It would have been about a 30 minute job if I had been smarter.

removed the wooden cutter block rt side top and the air exst.vent guard lf side then with a phileps driver 2 screws holding the control knob assm.in. both control knob assm.rt&lf come off the same way. just scraped out what that was left of the old lens stuck in new one and reatached light bulb holder. this bulb holder presses on and slides side ways to lock in place. then snaped control knob assm. back in and tighten the 2 screws. replaced vent guard & wooden cutter block. all was done.

perfect

Pulled out electric heating element and replaced with new. I have had this frustrating problem for 2 years and after replacing the elements they now work like new! My only question, why did it take me so long to replace???

I just pulled the electric element out of the slot and dropped the drip pan in place and slipped the electric element back in place and it was ready to go. It looks almost new. We built a new house in 95. It took 17 months to build it. I got the stainless steel cook top that you can have the grill on one side or you can pull the grill off and slip in the burners. It is only 4 burners but it is plenty to work with. It has a down draft.

First I turned off the power to the appliance. Then I took off the face plate where the switch and burner controls are mounted (took off 2 screws). Pulled the assembly out as far as wiring would allow and removed the two wires from the switch followed by removing the two nuts that hold the switch in place.
I reversed the process to install the new switch, turned the power back on and that was that.

Two dials available, chose the wrong one, PartSelect paid to have the wrong ones returned and issued credit, while helping to select the correct ones. Friendly, REAL people, who absolutely sealed the deal. I'll always check here first for parts, filters, anything. Thanks PartSelect

old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.

Removed 2 screws and i nut. Unplug the old switch and plug in the new switch and presto, back in business. Extremely easy. Part was exactly as pictured. Part arrived within 2 days. Great Co. to buy parts from. Highly recommend Partsselect.