Models > PGS975BEM4BB > Instructions

PGS975BEM4BB General Electric Range - Instructions

All Instructions for the PGS975BEM4BB
76 - 90 of 142
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven meat probe broken
This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.
Parts Used:
Meat Probe Thermistor
  • robert from FAIRFIELD, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the lower oven gas igniter
Flip toggles to release the oven door. Pull up on oven door to remove. Put door aside. Lift enamel bottom. Slide strait out. Remove aluminum shielding from around the igniter. Loosen igniter, unplug the igniter. Remove burner cowling. Plug in new igniter. Attach cowling to new igniter. Screw it all back in place. Stuff wiring connected back through the protective hole. Depress close door button and test. It takes about 10-15 seconds to ignite. Reinstall aluminum protector. Re install bottom enamel piece. Carfully slide oven door back on pegs and flip toggles to lock. Have a big glass of water and yell, Honey I fixed the oven!!
Parts Used:
Oven Igniter
  • Edward from New York, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Failed ignighter
Repair is easy. The keeper ring installation while holding the spring down was tricky. An extra set of hands is helpful in holding and replacing the keeper ring.
Parts Used:
ELECTRODE TOP
  • Connie from WESTFIELD, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Temp probe was defective
Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.
Parts Used:
Meat Probe Thermistor
  • Eric from SOUTHBURY, CT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced
the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.
Parts Used:
Top Electrode Mounting Clip
  • Dana from LEEDS, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Stove overheated with an F2 error
Removed screws holding temp sensor, pulled wire out from behind wall until found connector, disconnected old sensor.
Measured resistance of old sensor and compared with new sensor, they measured nearly the same. Installed the new sensor and tested the stove. Came up to temp ok. No problem since, about 2 weeks.
Parts Used:
Temperature Sensor
  • Richard from PHOENIX, AZ
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F2 Error on Display
The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back panel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.
Parts Used:
Temperature Sensor
  • Tom from FORNEY, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lower oven would not light consistently
I did find instruction in the Q&A on how to to change the part was for an older oven.

Here are the instructions that matched my oven model "JGSP42SET1SS"

https://www.youtube.com/watch?v=aHg-O1-NnXM

I also had issues where the connector for the new part would not come through the hole in the back of the oven. I used a shoestring around the connector so I would have a good grip on it when I disconnected the old igniter.This allowed me to have a good grip to reconnect to the new igniter.

While you have this apart I would also recommend that you remove the burner and blow out any material that may have accumulated over the years,
Parts Used:
Oven Igniter
  • Brad from PARIS, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
gas burners not heating evenly
remove old burner, put new in place
Parts Used:
Small Burner - 5K Burner Head - Large - 12K Burner Head - Medium - 9500
  • Juanita from GAINESVILLE, GA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Parts Used:
Temperature Sensor
  • Ron from SAN TAN VLY, AZ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace Thermostat
Pull oven out away from the wall, unplugged from outlet, removed center cover by removing 5 sheet metal screws. disconnected thermostat sensor from control cable. Opened oven door and removed screw that holds thermostat sensor. Pulled thermostat sensor out replaced with new sensor. Plugged sensor in to control cable. Replace panel and screws. Then my wife made me clean the oven. I recommend making the repair when your wife is not home.
Parts Used:
Temperature Sensor
  • Russell from Morgantown, WV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom Heating element quit working after 30 years
Removed several screws and removed element. Replaced same. Total ten minutes.
Parts Used:
Screws - Package of 12
  • Harry from Dills burg, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bake cycle would not work
open the oven door (remove) ,disassemble the igniter ,replace the igniter .
Parts Used:
Oven Igniter
  • Jenn from FORT WORTH, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
worn and pitted burner caps
Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.
Parts Used:
Burner Cap - Large
  • Ann from Ashland, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
very easy
there were no grate pads so it was easy to add them.
Parts Used:
Grate Foot
  • ROBERT from CYPRESS, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PGS975BEM4BB
76 - 90 of 142