PFCF1NFXAWW General Electric Refrigerator - Instructions

Slide it over the fill hose and just line it up and put it in the slot.

Since the mechanisms were in the freezer icemaker area, we deduced it was the fan motor. Ordered that from your store and it was delivered to our door in two days. Great service.

The part was replaced and our refrigerator has been quiet for the first time since we moved in almost four years ago and the refrigerator was new.

Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

had to rewire the harness in place in freezer. should have removed door for more room to work . easy job if you have 4 foot arms and a 1 foot chest.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.

Parts were perfect. Shipment great. It took a bit of time to get back to the Evaporator fan, so i basically had to take the entire freezer apart. Not a problem. The one issue i ran into was my unit had 2 white wires which connected to a silver bullet thing, that were not included in the wiring harness. Maybe I could have ordered that part (thinking out loud) I had to cut the old one apart, and adapt them into the new one, which had 2 holes to spare for this purpose. I guess i could have spliced every wire, but didn't. The freezer now SOUNDS LIKE A FREEZER. Thanks,

No need to shut off the water supply. A pair of pliers was required to remove the old filter, and the new one went in with just a quarter turn. It locked in place with no water drips. Less than 5 minutes to install.

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

Followed the video instructions with the help of a young man who worked on trailer hitches before and knew how to splice wires. Beware of splicing the wrong fan motor back into the assembly. . . . That happened here and we had to start the splicing all over again with the correct fan motor.

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

I followed the video provided by PartSelect, very helpful. I had to cut and splice 4 wires. The repair was successful. The replacement part was an exact duplicate of the original. I still notice the same sound but one tenth the volume. I hope the problem does not return. Many thanks to PartSelect for information to identify the problem and prompt shipping of the repair part.

Had to remove all the covers and fans to expose the condenser, which was difficult as the parts were frozen to it. The styrofoam covering the condenser made it almost impossible to defrost it. Therefore, I ripped the styrofoam off to expose the condenser. Was not really difficult to fix the styrofoam cover using metal tape. Replaced temperature sensor in aluminum block, and used butyl sealant to secure. Had to also re-install parts of ice-ball kit that were not well covered. Lots of parts to keep track of, but anyone could do it.