PFCE1NJWCDWW General Electric Refrigerator - Instructions

Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.

The problem began when freezer thawed and could not keep food frozen. Initially, I thought the issue was the defrost heater (because I had seen similar symptoms previously and resolved the issue with a new defrost heater)and I replaced that part with a spare that I had puchased previously. The issue was still unresolved and I noticed the evaporator fan was not running in the freezer because it would not turn on when I closed the door. I checked to make sure I could hear the compressor working (and it was)and concluded that the evaporator fan motor was not running. I ordered the part and found a YouTube DIY video on how to replace it. While I was at work, my fiancee took it upon herself to watch the installation video and install the new evaporator fan motor and all is well.

Ironically I did this today, as this email request came up asking how it went. I'm not a repairman, I'm a software engineer, and I can't thank this site enough for the step by step videos. With the video to help, this was a breeze, I was nervous as I had to empty all my freezer out onto the living room floor. Once that was done the repair took about 30 minutes. Thank you partselect!!!!! My second time doing business here, and I'll be coming back (well, if something breaks, so let's hope I don't have to).

watched a 2 minute video on installing the connector. Then using the utlity blade cut out a 1/3" section of the tubing and installed the connector. DONE! Leak fixed

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.

no brainer,watched the video,worst thing was to thaw the freezer,it was realy frosted,works like new,very happy thank you.

had to rewire the harness in place in freezer. should have removed door for more room to work . easy job if you have 4 foot arms and a 1 foot chest.

Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.

Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.

Parts were perfect. Shipment great. It took a bit of time to get back to the Evaporator fan, so i basically had to take the entire freezer apart. Not a problem. The one issue i ran into was my unit had 2 white wires which connected to a silver bullet thing, that were not included in the wiring harness. Maybe I could have ordered that part (thinking out loud) I had to cut the old one apart, and adapt them into the new one, which had 2 holes to spare for this purpose. I guess i could have spliced every wire, but didn't. The freezer now SOUNDS LIKE A FREEZER. Thanks,

follow repair viedo

followed part select video instructions

Used small screw driver to pry the top of the switch away from left inside wall of freezer side of side-by-side refrig./freezer; then used pliers to remove the switch; then removed the 3 prong socket and plugged it to new switch and installed it into the inside wall of the freezer.

Removed broken plastic attachments still connected to freezer ceiling by screws. Needed to take drawer slide from broken kit to install on new divider kit. Installed new divider kit with screws to freezer ceiling (used a little caulking around each screw as an insulator for screw holes). Installed with a little extra effort the cross bar upon which lower portion of dividerd sits. Installed ice tray and baskets.