NGD4600YQ3 Dryer - Instructions

First, let me say the t videos are excellent. Check them out if you haven't already.

I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.

I took a chance and ordered the maintenance kit to avoid having to take the dryer part to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .

Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.

Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.

As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.

It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.

One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)

It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.

Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.

Removed old filter, replaced with new.

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

remove back of dryer and install part same as old part was installed

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan

I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...

Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!

The rear seal in my dryer had worn through and burned up, so it definitely needed replacement. The squeak, however, originated in the motor (which I found out after replacing the seal and drum belt). Because of the age of the dryer, I was unable to remove the motor from the blower assembly (over the years, the shaft of the motor had fused with the blower), limiting my ability to oil the motor. Not good! The motor has since bit the big one!

Followed the included instructions in the Maintenance kit. Very easy to understand & follow. Only advice is to have an extra set of hands to assist in re-installing drum w/ the new belt. Entire disassembly & reassembly could be done w/ basic hand tools but went alot quicker using a cordless drill w/ a set of nut/screw driver bits.

I followed disassembly directions found on youtube and replaced th two-piece ring bearing that was identified by a parts diagra fron PartSelect. The repair was easy. Fix time was about thirty mionutes.

Took apart front of cabinet, set aside. Undid the belt drive. Removed the drum. Noticed rear seal was with large gap where it wore away, causing the lint to leak onto the interior of cabinet. Ordered a new seal, removed old seal, prepped for new seal. Used spring clamp to hold new one on place. Applied the glue to hold seal in place waited 24 hrs to dry. Reinstalled drum, put cabinet back together. Plugged in ran whisper guiet.

1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly

Recommend 10" or larger 14" will definitely do the job

2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatural

3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example

Two parts were needed in order to convert the dry back to Natural Gas. Part Select is usually good, but dropped the ball completely on this one. I received the correct Orifice, but was not asked or told about the need for the part for the regulator so the gas pressure would be changed back to Natural Gas. I found one at a local supplier and finished the switch. I chose to change the belt while in there because the dryer sounded like the belt had a chunk missing with the rhythmic thump. After installing the new, I found that one of the tumble paddles had a penny flopping inside it. One thump per revolution. This is the first in my career that the technician had not left the original orifice and regulator cap attached to the dryer.