NAV4200AKW Amana Washer - Instructions

Hving read some of the tips in regards to this repair I set out with equal parts of confidence & apprehension. The advice of shifting the tub toward the hinge to be removed is in itself the key to the whole procedure. After having done so & wedging a dust pan handle between the tub & frame to first one side & then the other, I removed the entire lid with the hinge & hinge pin assys. attached as ther is not sufficient clearance to slide a servicable hinge pin from a hinge when only one hinge has beeen removed. With the lid completely removed access to the hinge pin(s) is straight forward. I suggest screwing & unscrewing the fastening screw into a new hinge assy before mounting the hinge onto the machine & also using an offset philips screwdriver or ,as I did, a 1/4" drv. ratchet with a #2 philips apex bit which allows for a better feel & more control over the upside down blind operation of removing & replacing the fastening screw into the hinge assy. Hope this helps. Tom

Removed one bolt, main thing was I had to buy a 10 inch extension for the socket and wrench to reach inside of the agitator, pulled the old one off replaced the new one tighten the bolt and I was done. 10 minutes start to finish.

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

unscrewed screw holding old actuater in and replaced it whith the new part.

First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than 50 bucks i saved over 200 bucks by not going out and buying a new machine.

On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.

Top loader May Tag washer with open bottom. After research I presumed it needed a new belt, or Transmission, which runs 3 pulleys under the open bottom. After tipping the washer back for inspection, saw oil splatter underneath. Removed old belt by turning largest pulley on Transmission while pulling the belt "off" the edge. Belt was aged, Stretched and worn. Belt and all 3 pulleys were oily causing slippage. The main large Drive pulley on the Transmission shaft, has a plastic snap on grease cup at it's center. I snapped it off with screw driver. The cup was partially full of thinned old grease causing the oily mess. There's a C clip inserted in a groove on the end of the drive shaft holding the pulley on. Removed the C clip with screw driver tip and slid off the Drive pulley. The Center of the pulley contains a plastic ratchet assembly that operates the washer tub cycle to rotate and stop and repeat. The ratchet assembly falls right out, and in the end of transmission is a Thrust washer which can be pulled of easily also. I Cleaned all 3 pulleys with De-greaser and finally with Rubbing Alcohol to dry the pulley surfaces. Then cleaned and removed all grease from the plastic ratchet assembly parts and cleaned them. Then I Repacked everything including the Drive shaft with "heavier" Grease that would not break down so easy. Reassembled everything in reverse and installed on the shaft. Snapped the C clip back on to hold pulley back in place and then the Grease cup, which just snaps back in place with a push. Installed new drive belt in the same manner it was removed, only in reverse by turning the pulley, and pushing the belt "on" over the edge of the pulley. Problem fixed and washer works perfect again with Noticeably better operation through all washer cycles.

Hardest part was finding part that needed the needed repair. Searching the web for issues associated with the sound resulted in many links. Once the sound was found, I went to the video to see how to remove the Water Pump so I could examine it to confirm that was the correct piece. It took about 15 minutes to remove the part. Since I had to remove the belt to get it out, I realize that the belt needed replacement as well. So both parts were ordered. Replacing the parts also took about 15 minutes. Relatively easy repair. Be aware that the video on the part select video shows the water pump in a different location than the Maytag washer. To get to the Maytaq water pump, there is a panel in the back that had to be opened to access the water pump.

used video provided on repair procedure.

We followed the instructions show on the video. However, our model was assembled slightly different. We had to remove the screws from both sides of the side panels so that we could remove the tub from inside of the machine. Also our model only has one belt not two.
Over all it was easy considering my husband and I had never attempted to repair a washer. Once we got it back together it when back to working like it had never been broken!
We would have never been able to repair our washer without the video that your site provided... thanks so much!!??

Sure wish the manufactures would consider making the older models again as lots of us are not happy with the new modules being manufactured presently!

I pretty much followed the video,and read some of the other comments on how to do it. I only had one problem, the back panel had an opening of about 14"x14" to access the 2 rear balance springs. I finally laid the machine on it's face,so I didn't have to kneel down.The only problem with that,is the tub falls forward, making the springs farther away from the upper hole to attach/stretch, the springs to remove/install. I cured that problem by cutting a wedge out of a piece of 2x4, and stuck it between the top edge of the tub & upper frame. Worked great,held the tub in position, closer to the springs & locating holes. Taking them off is no problem,installing them, was made easier by using the wedge. The parts were a perfect fit, no more 'walking away from the wall' now! Thanks PartSelect

Unlike most videos, mine had a solid frame, no access panels. Following, is my disassembly & repair: I disconnected the water supply lines and drain hose. I slid the washer out into the center of the garage & removed the 9 base screws from the base plate. I slid the frame away from the base, leaving the working parts exposed. After pulling the working mechanisms from the outer frame, I turned it (drum, transmission & base) upside down. I used a pair of vise grips, pinched them onto each spring & removed them, using a downward motion it was a lot easier. I placed the base plate aside, removed 3 opposing screws holding the snubber ring & put 3 longer 8-32 screws in to hold the brake assembly. Then I removed the 3 remaining screws, lifted the plate & replaced the ring. Then I reversed the process, replacing the old springs with new ones & finished the job in about 2 hours.

As described in video; however, the video does not match the model I repaired. Most stuff is the same. Hardest thing to do was installing the new springs on the back of the tub (2 of them).

removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..

Brought unit out to garage so I would have room to work on it. Popped the top off, removed two screws to remove the front panel, removed back panel also, since there was no way I was going to the trouble of dis-assembly to get to the snubber without changing those 6 springs also - and you HAVE to remove the back cover to access all 6 springs.Removed belt and level and drain hoses- tub came right out. Loosened those 6 screws without removing them and pulled old snubber out- very straight-forward. Spent 10 minutes just comparing the old and new snubbers- I saw that there's a "ridge" around the inside of the new part that is gone on the old snubber. Sprinkled some corn starch at base of unit where the new snubber will fit (Great Idea someone had!) After everything was re-assmbled, I noticed the tub was now nice and tight when I grabbed it to move it. Before, it took no effort AT ALL to move it all around. Did a test load with some laundry the wife had stacked on the drier. Imagine my disappointment when I heard loud knocking inside when it started to agitate, but not while it spun!
Got all my tools back out and took the wet laundry out to take it all apart again- found the wife's heavy glass vase had been hidden in one of the towels. Re-tested- everything works GREAT!So far I've changed the drum seal (hardest) and the waterpump (easiest)- thi springs and snubber was alsmost as easy as the pump.
Above average shipping from Parts Select also- very helpful and efficient people on the phones.