MGR6751BDS Maytag Range - Instructions

I unplugged the power cord,removed the back panel and unplugged all the wiring harnesses.four screws hold the control in place. reverse to install. The instructions were very complete(I do this for a living so it was extra easy)Anyone following the directions could replace this in under 15 min.

I removed the two screws that attach the sensor to the oven wall. Then removed to more screws in the back of the oven and took off the rear cover, diconnected the sensor connector and installed the new sensor.

After reading some of the repair stories, I was hesitant about doing this task. It was really very simple, I just removed the screws from the back of the stove, and removed the old element. I then replaced it with the new one and replaced the back cover. This whole task from start to finish took 10 minutes. The oven heats perfectly now just like a new oven.

Had to unplug unit, remove back of unit (6 screws), then unscrew oven sensor (2 screws), then unplugged old sensor, replaced it and put back of oven on...Moving the oven out and working in the tight space avaialble was the most difficult. Other than that, super easy job that probably saved me a lot of $$$...

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

I had the old oven rack in the oven when I cleaned it. The rack came out brown and would not slide easily. The new rack was exactly the right one and now all is back to perfect!

Removed old ingniter with screwdriver. Installed new igniter, but had to remove connector in order to electrically connect using twist on connectors.

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland

Pulled stove from wall, removed sheetmetal back to electronic controls at the top of the stove. removed and replaced the electronic clock control modual, plugged in and tested clock and oven. moved stove back in place. thanks for the quick response on the part, I was surprised to get it in ONE DAY. We live in Maryland shipping point was Pennsylvania.

Removed back of stove, removed screws from sensor inside oven, unplugged connector from back of stove, pulled sensor out through oven; installed new sensor, replaced back of stove. Set the oven to bake, waited for it to pre-heat; the oven thermometer showed that the same problem was occurring, the sensor replacement didn't work.

After shutting the main valve behind stove. Removed all shelves and rear cover from stove. Unplugged the plug to the sensor. Removed the two mounting screws and pulled the old sensor out. Installed new sensor and plugged it in again. After reinstalling the rear cover and shelves, replugged in power, openned the gas valve behind the stove and tested with soapy water to make sure there wasn't ant developed leaks. Turned on oven with a test thermometer in it. Monitored operation and now oven temperature is roughly 10 to 20 degrees to the setpoint.

Repair was very simple. Took the door apart in layers, replaced the glass and put everything else back. it took longer to clean the stove than it did to actually take it apart and put it back together. guess i didnt need to be that much of a clean freak!

So, the F9 error indicates a electrical power issue. First I pulled the oven out and verified I had 240 volts at my outlet.

Then I removed the fire panel over the terminal block and the issue was apparent. The nuts on the terminal block were corroded. This had cause the resistance in the connection to raise and burn up the wire to my oven plug at the terminal block.

I removed the whole back panel and everything else seemed OK visually.

1. I go new connectors for the oven plug, stripped the wires, and crimped on the new connectors.

2. The terminal block DOES NOT come with the nuts to connect the wire to the terminal block. Mine were so corroded they had to be replaced. So I went and purchased the correct ones and installed the terminal block and reconnected all the wires.

3. I applied some dielectric grease to the connections through out the process of reinstalling to prevent it from happening in the future.

My husband and I began to pull the oven out and I realized that it was too heavy for me to hold. Luckily we were able to get another man to help. Other than that it was easy. Also, it took us awhile to figure out which screws secured the oven into the cabinet. We saved over $1000.00 on a new oven and installation. Kudos to everyone who added their comments! They gave us courage to give it a try.

I took the oven door apart, pulled out the broken fragments of glass and replaced it with the new glass. I should have taken notes as I took the door apart because it was a bit tricky to remember how all the pieces fit back together.

I was very impressed with how quickly the parts were shipped and the quality of the packing materials to protect the glass as it was shipped.