LDS5040ST LG Dishwasher - Overview
Models starting with LDS5040ST
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Hinge Cable
PartSelect #: PS3524406
Manufacturer #: 4933DD3001B
The door hinge cable works in conjunction with the dishwasher door by connecting the door hinge to the door spring and helping to support and balance the weight of the door as you open and close it. I...
$24.61
In Stock
Dishwasher Roller Assembly
PartSelect #: PS12075858
Manufacturer #: 4581DD3003C
The dishwasher roller assembly connects to the dishrack, and is located in the lower level of the dishwasher. It allows the dishrack to easily slide in and out. If the lower rack keeps falling off the...
$17.44
In Stock
Gasket
PartSelect #: PS17267570
Manufacturer #: 3920DD3005H
If your dishwasher is leaking or not cleaning as well as it used to, the door gasket might be the culprit. This flexible rubber seal fits around the tub and keeps water and steam inside during each cy...
$82.48
In Stock
Dishwasher Nozzle Assembly
PartSelect #: PS7788355
Manufacturer #: AGB73093001
This nozzle assembly, commonly referred to as a spray arm, is located at the bottom of select LG dishwashers and is responsible for distributing pressurized water across dishes during the wash cycle. ...
$80.21
In Stock
Drain Hose Assembly
PartSelect #: PS11732679
Manufacturer #: AEM69493807
Replacement dishwasher drain hose. Per the manufacturer if the drain hose being replaced does not have the vent tube going to the water inlet assembly a new water inlet will be needed.
$138.68
In Stock
Dishwasher Holder
PartSelect #: PS6012668
Manufacturer #: MEG62279201
Finding the right parts for your dishwasher can be tricky, but were here to help. Consider this Dishrack Roller Bracket by LG? an authentic, OEM part designed to keep your dishwasher operating at opti...
$17.44
In Stock
Dishwasher Water Inlet Valve
PartSelect #: PS8769826
Manufacturer #: 5221DD1001E
This part is the replacement inlet valve for your dishwasher. It is approximately 4-1/2 inches by 3-1/2 inches. The water inlet valve in your dishwasher connects to the water source and solenoid wire...
$125.86
In Stock
Hinge Spring
PartSelect #: PS3524563
Manufacturer #: 4970ED4004D
Is your LG dishwasher door not staying firmly shut or opening too abruptly? Then, our LG Door Hinge Spring is the solution you're searching for. Designed exclusively for specific LG dishwasher models,...
$36.43
In Stock
Common Symptoms of models starting with LDS5040ST
[Viewing 11 of 11]Leaking
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Not draining
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Not drying dishes properly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not fill with water
Fixed by
these parts
these parts
Show All
Will not dispense detergent
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken door spring allows the door to overextend to the floor if not propped.
Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was broken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.
Parts Used:
-
Gregory L from INDEPENDENCE, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
34 of 41 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher door became heavy and would fall to the floor if you didn't hold it up.
Removed mounting screws from sides of disher. Removed broken piece of connector assy still attached to hinge. Attached new connector assy to hinge then looped it around pulley with spring attached to opposite end. Need both hands to pull spring up to side of tub and connect it. I would suggest replacing both connector assemblies while you have the dishwasher pulled out. Push dishwasher back in and mount with screws.
Parts Used:
-
Charles from DENNIS, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
32 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The hinge spring and/or connector assembly were not functioning, so the dishwasher door was extremely heavy.
Replacing the spring and connector assembly (the cord had frayed and broken) was easy and took only a matter of minutes to do. Wrestling the dishwasher in and out of its space under the counter was very difficult. Because my kitchen is compact, I had to move the refrigerator first, then disconnect the Romex cable and water lines from the dishwasher before I could pull it fully from under the counter. The side panels have screws in the front and the back, so the appliance had to be moved out until its back was exposed. But I got the job done and the door works just like a new one now!
Parts Used:
-
David from NEW ORLEANS, LA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Wrench (Adjustable)
11 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!