Electric Drill Parts

Your Price

$23.95

PartSelect Number PS10153834

Manufacturer Part Number 664064-4

Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord

Your Price

$5.95

Electric Drill Compression Spring

PartSelect Number PS11929265

Manufacturer Part Number N019351

Keep your bit holder secure with this genuine OEM spring for DeWalt impact drivers. Authorized by the manufacturer and sold individually, this durable metal spring is designed to maintain pressure on the N078437 sleeve and the rest of the bit holder assembly, ensuring that the bit stays firmly in place during use. If the spring fails or becomes worn, the bit may no longer be held securely—making replacement essential for safe and effective operation. This part is commonly used in a variety of DeWalt impact drivers and requires only a screwdriver for installation. Simply disassemble the bit holder assembly, remove the worn spring, and install the new one in its proper position to restore full functionality.

Your Price

$6.95

Electric Drill Cord Guard

PartSelect Number PS10153918

Manufacturer Part Number 682502-4

This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually require replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.

Your Price

$5.95

Electric Drill Hog Ring

PartSelect Number PS11927770

Manufacturer Part Number 608114-00

Secure your sockets with this genuine OEM Hog Ring for DeWalt Impact Wrenches. Made of durable metal and sourced directly from the original manufacturer, this high-quality part fits onto the end of the anvil to help retain sockets during use. Over time, hog rings can wear out, become damaged, or go missing—affecting tool performance and socket stability. Replacing the hog ring is a simple repair that requires only a screwdriver. Carefully remove the existing ring from the anvil, then position the new one in place and secure it using the appropriate fastening method. This part is sold individually, so be sure to order the correct quantity for your tool.

Your Price

$30.01

Electric Drill Charger

PartSelect Number PS17016372

Manufacturer Part Number 90593303-01

This is a genuine Black and Decker replacement charger, sold individually. It’s designed to recharge the battery used in the cordless tools listed below. Over time, chargers can wear out or stop functioning properly. Replacing the charger is a cost-effective solution that can extend the life of your tools—often much less expensive than purchasing a brand-new unit.

Your Price

$15.95

Electric Drill Ball Bearing

PartSelect Number PS10141520

Manufacturer Part Number 211031-6

Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Your Price

$14.95

Electric Drill Helical Gear 41n

PartSelect Number PS10142974

Manufacturer Part Number 227769-3

This is an authentic Makita replacement part that has been sourced from the original manufacturer to be used with drywall screwdrivers. The metal gear is used to drive the spindle by interconnecting with the armature's gear. This item is sold as an individual replacement part.

Your Price

$31.95

Electric Drill Power Cord (8-foot)

PartSelect Number PS10153856

Manufacturer Part Number 664630-7

This cord is a genuine Makita replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 18 Gauge • 8 Feet Long

Your Price

$31.95

Electric Drill Variable Switch

PartSelect Number PS10153474

Manufacturer Part Number 650208-2

This Trigger type VAR switch has 4 internal terminals and a locking mechanism. This genuine Makita replacement part is sold individually. Switches are commonly replaced parts in power tools. A switch handles on/off and variable speed functions. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. Some common signs of a broken or failing switch are: • The tool has completely stopped functioning • it will not turn on. • The tool operates intermittently, requiring multiple tries to turn on, until eventually it won't turn on at all. • The variable speed function and electric braking aren't working properly.

Your Price

$14.95

Electric Drill Ball Bearing 607llb

PartSelect Number PS10141514

Manufacturer Part Number 211021-9

This replacement ball bearing is an authentic Makita item. It is supplied directly from original equipment manufacturer for use with angle grinders. Please check diagrams for proper application of this item. The bearing is specially designed to reduce friction between rotating parts. Over time it will wear out and will need to be replaced. This is a sealed metal bearing and it is sold individually. Included in part number 515616-3

Top Brands

Top Product Types

Popular Electric Drill Parts

Electric Drill Brands

Popular Electric Drill Models

Electric Drill Parts

Find Your Part

Popular Electric Drill Parts

Electric Drill Brands

Popular Electric Drill Models