KBULT3661A ((01)) Thermador Refrigerator - Instructions

The ice maker is held in by three screws. There is an electrical connection. Also, there is a water line to the rear of the unit.
The replacement unit had clear instructions and a selection of parts to match the defective device.
Hint: don't discard the old unit until the new unit is configured for installation.
Turned on the water and the electricity to the fridge, and had ice in several hours.

Removed one screw on cover covering wires on old ice maker,disconnected plug, removed ice maker, checked connector to make sure there was120vac, Power supply was good, installed new ice maker, connected plug. Works great.
Part to fix ice maker is very expensive, complete unit only $15 more and it has a one year warranty.

With a little investigation, I found that the ice tray had corroded, and the increased friction was keeping the ice from dumping out properly. It also had apparently damaged the gear motor, and the timing of the ice ejector was off. I went to the Part Select site and found that the icemaker specifically for my refrigerator was significantly more expensive than the universal Whirlpool replacement icemaker, but the two looked similar, so I ordered the universal replacement. When it arrived about 3 days later, I was able to easily remove the standard parts and replace them with the plastic parts and wire harness that were unique to my refrigerator. They fit perfectly, and I had the new icemaker installed in only about 20 minutes, including time spent to remove and replace the plastic parts

it was very very simple, it took only three screws
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in the medical profession, IF I CAN do it , everyone CAN!!!!!!!!

It was very fast and easy. Two screws to take of the ice door cover. the ice maker itself just slid out and all I did was disconnnect the wiring harness. Unscrewed the plastic bottom case and screwed onto the new one. Attached the harness and slid it back in.

i can't believe it was that easy, just removed the screws, pulled elements out disconnected wires well it seemed to easy so had to read the directions or it would have took only 10 minutes. to do this job. thanks so much for your web sight, the repair man said it would probably be 200.00 or so

yea right 100.00 and its making all the ice we need thanks

joan mcquain

unscrewed 4-5 screws; unplugged; attached arm; installed; reverse pattern. truly easy. cost 1/3 what repair man quoted me. this is easy!

Replacing the ice maker is no big deal. Just take out the old one and replace it with the new one. The replacement, however, didn't work very well. Seemed like its timer was off, so it would dump ice cubes before they were completely frozen. So, we go shells of ice cubes. Not good. Called Parts Select, advised them of the problem, and they agreed to replace the part. Could not be happier with the customer service I received from this company.

I first removed the bottom screw then loosened the top two screws about 3 turns lifted an then slide icemaker out a couple inches then used small screwdriver to unclip the wire conector and removed icemaker then pluged new icemaker in and tightened top screws replaced bottom screw lowered metal arm and was done. les than 10 min. it has taken me longer to write this reply than it did to install the icemaker.

Unscrewed 3 screws. Unplugged the old unit, plugged in the new unit. Replaced 3 screws. Made ice like new.

This was VERY easy. The kit inlcuded every conceivable wire connection pigtail. Turned out I needed none since the OEM cable was a plug & play affair.

First I unpluged the refriderator and removed the old ice maker. I then just simply installed the new ice maker. It was just that simple. The next morning I woke up with a full tray of ice.

This was an easy repair.

First I turned off the breaker that supplies power to the refrigerator, then I followed instructions to remove the old ice maker. I removed the bottom screw and loosened the two top screws and it came out easily.

The only unexpected problem I ran into was that the connection at the refrigerator end was 'hard wired', i.e., the wiring harness was not removable from the freezer.

After disconnecting the wiring harness from the old ice maker, all I had to do was plug the wiring harness into the new unit, slide it into place, then replace the bottom screw and tighten the two top screws.

Turned the power back on and had ice within 1/2 hour! : )

Unplugged the fridge. Got a light to shine on 3 small screws. Used a pair of channel locks to get the pigtail wiring harness off and the old one was out. Put the new one back in, plugged in the wiring harness and heard the ice bin getting it's first new ice a few hours later.

After diagnosing the ice maker wasn't working, I got the model & serial number of the refrigerator. Picked the ice maker online by picture, that was a first. Three screws to take the old one out and replace the new. Written directions confirmed there is no manual cycle button on ice maker. Waited a couple hours and checked it, there was ice! Everybody was happy.

I pulled off the filter tab, unscrewed the filter and installed the new one. It was that easy!