JTB2488AEW Jenn-Air Refrigerator - Instructions

Watched the video, big help.

removed the cover from the back of the refrigerator, and used the nutdriver to loosen screw on the single outlet water valve, removed the old water valve and the hoses to it. Connected the hoses to the new valve and attached to the wall of the refrigerator by tightening the screw. Then removed the old ice maker from the inside of the refrigerator, by loosening the two screws and attached the new one, I tightened the screws and then I was done. It is working great.

Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cable wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!

Instead of the ice maker unclipping from the wall after one 1/4" screw being removed from the bracket, I had to remove three of the 4 Phillips head screws from the ice bucket slider below the ice maker and swivel it down to allow the ice maker bracket to clear. The two 1/4" screws holding the ice maker to the wall at the top had to be removed and then the ice maker could be pulled away from the freezer wall. The rest of the instructions went according to the video and went well.

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

installed new part easy

Popped rail off and replaced with new one. Video showed how to do it. A bit tight to remove and just needed a little strength and patience.

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

I merely removed the old one and replaced the old one, I luckily had a ratcheting screw driver which made things go alot quicker as there were 36 screws holding the gasket on the inside of the door, also I had to replace some of the screws that I tightened as they stripped out in the door metal, I GOT SOME OF THE SAME DIMENTION with a slightly larger thread new screws and carefully screwed them in with no problems at all. Thank you for your professional speedy service. I will surely contact you again when I need parts for my appliances even if I m not the MAYTAG repair man.

I took out 1 screw , unplugged the icemaker and lifted it out and installed the new one and had ice in no time at all. can't get much easier.

Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)

I unscrewed the support and replaced it with one that I ordered. It was fast and easy.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!