JS48PPDUDE01 Jenn-Air Refrigerator - Instructions

followed the video provided on website. repair was very simple / straight forward. Once emitter and receiver boards were replaced, issue with ice maker was resolved.

Over the last several years we have had several appliance repairmen try to fix the icemaker. One replaced the entire icemaker. We bought a booster pump for the water. After spending about $1,000 over the past few years trying to fix the problem, a plumber doing routine plumbing work looked at it, and said it might be the control board. I found instructions online how to test the control boards. I ran the test, and they failed. I ordered the parts from PartSelect, followed their easy instructions, and tested the new units. They passed with flying colors. We now actually have an automatic icemaker for the first time in years.

I had to remove ice storage compartment sitting above motor on door to expose auger gear. Then used a small socket to remove 4 screws from underside of auger motor compartment in door. Motor drops out with a small wiring harness attached. This simply unplugs and then swaps in with new motor. Auger axel was sanded to remove rust and grease applied. Motor door and ice compartment were then reattached.

diagnosed the problem to be the emitter and receiver boards. replaced in about 15 minutes. works like new!

Watched video of similar model repair for filter housing. But the model KitchenAide refrigerator requires enter and replacing housing from the back. My model has a metal facing which has doors attached to it also. It was simple repair though from the backside of the appliance.

Just needed to replace the water filter

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Put One card in one side and other card on the opposite side, push in on both sides to press in clips that hold light in. Once clips are in light will start to come out unplug light and plug in new light. Push light back in.

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

Easily removed old filter and inserted the new one

My icemaker quit 3 years back and at that time I searched for do-it yourself repair books with no success. I found this parts place web site and people having the same problems as myself. I purchased the parts as others have and problem solved! Ice all the time, woo hoo!

After unplugging refrigerator, removed emitter and receiver cover plates on each side of freezer unit (3 screws each) and mounting screws for circuit boards. Unplugged old boards and plugged in new ones and reinstalled boards and then cover plates. Although, indicator code lights seem to still indicate a problem, ice maker has resumed operating after 24 hr.

My ice maker about six months ago started to ice make very intermittently and eventually stopped all together. The emiitter no matter what I did was giving me two flashes then a pause, over and over again. I purchased the emitter kit and with a Phillips screwdriver in about five minutes my ice maker kicked the sulinoid on and ice was already started!!! Fast and easy repair!!!

I went online and watched a U-tube video that said it was most likely the electronic emitter and receiver boards and showed how to replace them. I first unplugged the appliance (just to be safe) then, I unscrewed the screws holding the faceplate on. The board simply has a plug which you unplug with a little care and effort. I then plugged in the new board, resituated it into the hole and screwed the faceplate back on. You simply do the same for the other board on the other side. Viola! Lots and lots of ice!! The guy at sears said I shouldn't do work on such a complex appliance. Probably because I am a woman! Anyone can do this job! Winning!