JKP18G3K3 General Electric Range - Instructions

First I located the circut breaker to the oven- once no power supply was confirmed (oven light was out) I diconnected the screws that held the old element in place. Pulled the old element forward and disconnected them from the wires. The hardest part was getting onto the oven to reconnect the wires to the new element since the door opens down the work space is a little tight and awkward. Connected new element and replaced screws. Done in less than 20 minutes and no repair service calls to pay!

My husband removed the old element by shutting down the power, then unscrewing the element. Then he screwed in the new element and turned oven on for 5 minutes to break it in.

Very simple and so cheap!

First I removed the two srews that hold the element in place. I then pulled the element out about three inches and disconnected the two wires. I attached the wires to the new element and we had our oven working again. I really am happy with the timely service I received from PartSelect and would recommend them to anyone.

I removed the two screws that held the element panel on. I removed the lead wires from the element, making sure the wires didn't retract back into the wall. I put the new element in, reconnected the lead wires and put the screws back in. I was concerned that the panel wasn't as long (top to bottom) as the previous one and it barely covered the hole, but it works fine. It would have cost me $60 to have it done by my home warranty company so I saved almost half.

I removed the two screws that held the element in place. I pulled out the element and disconnected the two wires and unscrewed the screws and then place the new element to it. screwed the wires back to the element wires and then push it back in. Replaced the outside plate and screw the two screws back in.

Save myself money by doing it myself.

Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.

Used a nut driver to remove two hex screws holding element to the back of the oven and then the two hex screws connecting the element to the oven wires. I pulled the element out and reversed the process. I turned the oven on and made sure the element worked.

First I shut off the circuit breaker for the oven then removed the screws that hold the element in place. The element was pulled out about 3 inches and unscrewed the 2 screws to disconnect the two wires. Upon receipt of the new element, I simply reversed the above process and the oven performed like new. Very easy, very quick and very grateful to have the oven operating again and it was a very inexpensive fix.

Turned off circuit breaker, took two screws out to be able to pull element out from back. Took two more screws out to remove old element from oven. Did the opposite to install the new bake element. Turned power back on, and it worked fine.

I removed the screws that held the element in place. This was the most difficult part because clearance was tight between the screws and the element. I gently pulled the element out enough to expose the wire connections. I disconnected the wires and removed the element. Installation was the reverse - connect the wires, re-position the element, re-install the final screws.

Had my youngest son removed the two nut screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed element and installed new element in reverse order.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires
the Replacement fit easily. Part was delivered the day after ordering even though I used normal delivery. Oven broke on a Thursday,ordered the part Friday morning, back in operation on Saturday

Removed screws from plate holding the element in then removed the screws from the wires attached to the element. Reversed the process and was finished. Oven is back in working order. (I am recently widowed and this is the first time I have had to do this type of repair)

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.