JGS9900BDS16 Jenn-Air Range - Instructions

Removed two star screws from the top of the burner, disconnected the wire going to the Ignitor, removed the old ignitor held in with one phillips screw, installed new ignitor and re-installed the burner assembly. Simple!

Replace the racks. No special instructions.

For the Ikea Range isg650ws01, the repair was very easy.

Step 1) Slide the range away from the wall slowly, verifying occasionally to not strain the gas or electric lines

Step 2) Unplug the range

Step 3) There are 2 phillips heads screws holding the rear panel in place. Remove the two screws and remove the panel.

Step 4) The cooling fan is held in place with 2 phillips head screws. Remove the screws and disconnect the electrical cord

Step 5) install the new cooling fan. The electrical plug can only be inserted one direction, so there shouldn't be a concern that you have the plug installed correctly. Match the original orientation of the fan in the unit. Re-install the 2 screws for the fan, and then install the rear cover. There are 2 slots that the panel needs to slide into in the bottom. Finish the install by installing the 2 screws you removed in to hold the rear panel. Plug the range back in and heat to 450°F to validate the repair.

To replace the igniter, I removed the oven door, all racks, the cover for the burner element and the shield over the burner element. I also removed the back panel to access the wiring. Removal of these elements was easy and took only a couple of minutes. When I tried to remove the old igniter from the bracket supporting it, one of the screws was stripped. Unfortunately I had to drill this screw out and replace it. If I didn't have to do this, both jobs would have taken about 20 minutes combined. After removing the igniter from the bracket, I replaced it, ran the electrical to the back where the wiring harness was and reassembled the components.

As for the upper oven temperature sensor, it took 5 minutes. I removed the two screws holding the sensor in place and pulled it out which exposed the electrical connection. I simply unplugged it, and screwed the new one in its place. I then connected the wiring harness.

I had to wait week for parts that were supposedly in stock No notice about delay I had to call to find out you really dropped the ball on this one

Turned off the gas line & unplugged the oven. Pulled oven away from the wall to access the back of the oven. Removed the back panel (screws) on the oven & the few inner oven parts covering the broken igniter. Sprayed WD 40 on the threads of screws holding the old igniter in place. Removed old igniter screws with a nutdriver & unplugged it from the back of the oven. Installed the PartSelect replacement igniter & plugged it into the wiring receptacle. Reassembled the parts covering the new igniter & screwed the back panel back onto the oven. Plugged oven in, turned the gas back on & pushed the oven back into place. Tested the new igniter. Woohoo, oven works again & wife if happy!

Take out 2 T15 torx screws. Lift burner assembly, disconnect igniter. Make sure wire does not return into hole. I put A paperclip on it. Connect new burner assembly. Clean under old burner. Install burner assembly with screws. Test burner.
Voila!

Once I got over my first time jitters this was easy. Lucky for me the old screws went back in just fine. The recommended 8/18 x 3/8 screws were way to small to be usable. Check the length of your existing screws if you can before purchasing the recommended ones.

This is a double oven unit. Both the upper and lower igniters are easy to get to, with just a few screws to remove. However in order to reach the quick disconnects, the back of the oven needs to be removed. So there are a bunch of screws to take off and the oven needs to be moved away from the wall. Pulling out the igniter wires and putting the new ones back in, is easy. Then put all the screws back on and move the oven back to the wall. Don't forget to disconnect the power when you do all this.

Removed the original rack. Checked dimensions, installed the new rack.

Removed two screw securing wburner and disengage igniter.

Ordered a replacement, removed the old burner and installed the new one. Works perfectly.

1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!