JGR8875RDB Jenn-Air Range - Instructions

Very Simple, I recommend pulling the old gasket in sections, and popping the new gasket metal holders in the holes as you go. You can't mess it up. For the ends, I tucked them in using a pair of needle nose pliers, but any small slender tool, such as a thin screwdriver, will work.

Diagnosed the issue by removing the bottom panel of the oven. (two little screws) Once the panel was out I turned the oven on with the door open to see what was happening.

Noticed that the heating element wasn't lighting up in order for the gas to ignite. Unplugged the oven and removed the heating element. Two screws hold the heating element in place. Removed those. Then, there is a panel on the back of the oven with one screw to remove. Once panel is removed you have easy access to the heating element connecting electric plug. Disconnect this plug by simply pulling apart.

Then, I was able to go back to the inside of the oven and slowly pull the heating element with plug out. The heating element had the part number on it. My oven is a Maytag which, is made by Whirlpool.

Went online to Whirlpool PartSelect and ordered my part. The part came in two days. Installed my new part and plugged in my oven to test the part. Part worked perfectly. Unplugged the oven and finished the installation process.

Removed the lower base pan of the oven by unscrewing two phillips head screws. I then had access to the old igniter and removed that by removing the mounting screws (2 Phillips head screws). Continuity test revealed an open circuit. I simply replaced the old part with the new part, reversed the process and the oven was ready for use in less than 10 minutes.

I took the door off, then took the bottom out removed two screws, unplugged the old igniter and installed the new one. I turned on the oven and tested the new igniter and then replaced the bottom and oven door.

Very easy install. Works great.

Unplugged the Rang. Removed the oven door. Removed the lower cover for the Bottom heater. Removed the two screws that held the igniter to the burner. Went to back of oven to disconnect the igniter. removed the old igniter. Installed the new Igniter in the reverse order.

Ordered the broiler igniter that matched my model from part select and installed. Easy and part works as it should. Only took a few days to get here and saved me $40 by not purchasing at a local parts store as well. Will use part select if there are any future needs.

It's happened before and the igniter has always been the problem. This time, however, the mounting holes were slightly off and had to be drilled out. The connector didn't mate up and so both had to be cut off, the wire stripped back and wire nuts used to make the connection. In the end, it all worked out. I guess since its kind of old, you can't stock every component for every oven. Oven works perfectly now.

I located the temp sensor (top left). Removed the 2x Phillips screws and slide the wire out until the plug is thru the opening taking care not to pull to hard as to damage the end that you not going to replace. To install plug it in and push the wire thru and secure with 2x Phillip screws.

1. Slowly pull the stove from wall. 2. Unplug 120 volts plug from outlet. 3.Turned off the gas outlet. 4. Open the stove door, remove the racks, then unscrew (2) screws that hold the short oven sensor in place. 5. Slowly pull sensor out of it's housing. Remove the clip that holds the sensor. Install new sensor using the clip. Push sensor back through the hole opening. Screw the (2) screws into the mount to secure the sensor. 6. Plug the 120 volt plug into the wall outlet. Turn on the gas outlet. Test stove by turning on oven. It works like a new stove. Wife is happy, and Thanks Giving Dinner is on! Reverse your steps to secure your stove. A total of 25 minutes after cleaning the dust under stove. Thanks for everything. By the way, Thanks Giving Dinner was delicious.

Unplugged the old temp sensor at the back of the stove. From the inside I removed the 2 retaining screws. I taped a string to the old wire and pulled it through so I could pull the new harness through on the new sensor. When the new sensor arrived I installed it in reverse order. Easy peasy. Works great!!!!

Removed all the racks from inside the oven, unscrewed the 6 screws that held it into the cabinet, pulled it out and sat it on the floor in front of the cabinet. Removed the oven sensor from the inside of the oven after disconnecting the wire harness from the rear right exterior of the oven. Installed new sensor from inside (2screws), plugged it into the harness in the back and reinstalled oven in the cabinet.

I removed the floor of the oven (one screw) and the heat dispersal shield (one wing nut). Then I detached the old igniter using a socket set. I had to remove the bottom drawer to unplug the ignitor and plug in the new one. Then I reassembled. Total piece of cake and I have no experience whatsoever.

Nothing to it - remove oven bottom, and burner cover, unscrew the 2 scews holding the igniter
(one of mine sheared off now only one is holding the new igniter in - it still works) unplug wire at the connector then reverse and the oven is as good as new. The best part is that I received my part in only 2 days.

The oven was inconsistanty lighting and I could not predict when it would. After reading some repair reviews I determined that the problem was most likely the igniter. I purchased one from your site and it arrived the next day. Awsome! Had to take out six screws to get to the wiring and removed the igniter. The wiring was a simple plug. Replaced the igniter in about 20 minutes and the oven has been working flawless every since. THANKS!