All Installation Instructions for General Electric Range JGB285SET2SS

Replace temp sensor in gas range

Part came as ordered. Hardest part was fitting plastic wiring harness through the hole with 2 layers of steel with insulation in between. Used electrical tape to stiffen the end about an inch or 2 back from harness. Job done, problem solved

Parts Used:

Range Oven Temperature Sensor

Ron from PAINESVILLE, OH
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burner cap wasn't working proper.

took burner off installed new one thank you for fast shipping

Parts Used:

Burner Cap

GLENN from ST CLR SHORES, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Food ran over the burner and damaged it.It was easy to place it back inII

It only required placing the new burner in the proper location.

Parts Used:

Burner Cap - Black - Medium - 9500 BTU

Alan from PASADENA, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner cap replacement

I got really great customer service on finally getting the right part. It came really fast it fit perfect but the cap is a high gloss black instead of a flat black. I will need to call customer service again to see if they can the correct color this time.
Otherwise everything was great!

Parts Used:

Burner Cap

Rita from ST AUGUSTINE, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken right END of oven door HANDLE (3 separate pieces assembled)

(Followed the ORIGINAL manufacturer's instructions for assembly we retained when purchasing the appliance.) Replacing the broken handle end involved removal of the LEFT handle end as well as the broken RIGHT end, the center rod handle, and unscrewing the outer door face from the inner door face. Had to find specialty screwdriver for non-standard screw heads. Sigh. It was impossible to replace the door handle, as it requires removing the entire door - It is too heavy for one person to hold in place while the 2nd person tried to blindly replace screws thru a 1/2 inch slit in the outer and inner door pieces. Hiring a handyman is impossible leading up to the holidays, so we decided to just buy a new stove. Something that should be really simple to replace for less than $50 is now a major budget outlay due to a crappy design.

Parts Used:

Door End Cap - Black - Right Side

Margaret from SARASOTA, FL
Difficulty Level:
Very Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable), Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

flame was inconsistent. too much air.

replaced old with new.

Parts Used:

Vision Burner - Extra Large

Raymond J. from EASTPORT, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Gas Range oven not heating/replaced new heating element

Removed oven shelves, removed lower cover, removed heating element, removed lower drawer and unplugged element.

Parts Used:

Flat Style Oven Igniter Kit

Andrew from EL SOBRANTE, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven wouldn't light

Remove interior bottom of oven, remove igniter screws, unplug igniter. reinstall igniter.

Parts Used:

Flat Style Oven Igniter Kit

David from FLAGSTAFF, AZ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

some of electrodes not working at times,found were bad,wires had some insulation missing, clips looked burnt,found all new parts replaced

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Parts Used:

Top Electrode Mounting Clip

Dana from LEEDS, AL
Difficulty Level:
Really Easy
Total Repair Time:
More than 2 hours
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Venturi Choke for LP gas (not used for natural gas)

The best thing for finding the part (only used on LP, so difficult to fine) was a young lady that I chatted with. She never gave up and keep looking as I tried to explain the part. Her name was Ashley!! Keep her she is truly worth every penny paid.

Parts Used:

VENTURI CHOKE 15K LP

Terry from SPRINGFIELD, CO
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

finish on old oven bottom was damaged

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

Parts Used:

BOTTOM OVEN AND DEFLECTOR ASM

ERNEST from MANCHESTER, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

First part tube too long Repairman $90.

2nd part fit but hole to allow gas out too large Scary when I turn it on! Waiting until Dec to have friend see if he can replace the gas opening part. See if part at end can be replaced by old one??

Parts Used:

NG BURNER TUBE

Marilyn from Boise, ID
Difficulty Level:
Very Difficult
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

BASE OF BULB BROKE OFF & WELDED TO SOCKET

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Parts Used: