JES9860BAW18 Jenn-Air Range - Instructions

SHUT OFF POWER AT BREAKER BOX! Remove oven door, use nut driver to remove two screws holding old element to back of oven. Pull forward to get wires into oven, remove wire clips from old part and re-attach to new element using pliers. Re-attach to back of oven, replace door. Turn on power and heat oven to burn off coating on new element. Not at all difficult, except for wire clips are at angle to wire, making re-attachment a bit difficult to do. DO NOT LOSE WIRES INTO BACK AS THEY WOULD BE VERY DIFFICULT TO RESCUE IN A JENN-AIR SLIDE IN UNIT LIKE OURS.

Turned off breakers to oven. Removed two screws that held oven in cabinet. Removed oven door by opening slightly and pulling up on door. Pulled oven out 1/3 of way. Took out four screws on top of control panel. Took oven light switch off by unscrewing holding ring. Removed temp knob on right by pulling. Removed start / stop knob same way.Removed glass straight out. Removed four screws that held elecrtonic clock conrtol board. Unpluged three wire plug from right side and the nine wire plug from the left side. Worked board out at and angle. Went backwards to connect and replace board, screws and door.Slid oven back in and tested oven after turning breakers back on, worked like new.

lift out old filter, wash, put in new filter.

Spoke to your very helpful staff, who advised me that a likely problem was the oven sensor. I took a chance and ordered the part, which came promptly. Your service video for the part was most helpful in my decision to try the part. Installation was a breeze, but it was the oven controller board that had failed and not the oven sensor. That called for a service professional, who ultimately fixed the problem. Your service though, was excellent and I would highly recommend you to others.

Replace the racks. No special instructions.

For the Ikea Range isg650ws01, the repair was very easy.

Step 1) Slide the range away from the wall slowly, verifying occasionally to not strain the gas or electric lines

Step 2) Unplug the range

Step 3) There are 2 phillips heads screws holding the rear panel in place. Remove the two screws and remove the panel.

Step 4) The cooling fan is held in place with 2 phillips head screws. Remove the screws and disconnect the electrical cord

Step 5) install the new cooling fan. The electrical plug can only be inserted one direction, so there shouldn't be a concern that you have the plug installed correctly. Match the original orientation of the fan in the unit. Re-install the 2 screws for the fan, and then install the rear cover. There are 2 slots that the panel needs to slide into in the bottom. Finish the install by installing the 2 screws you removed in to hold the rear panel. Plug the range back in and heat to 450°F to validate the repair.

Once it was identified that the Motor Relay was no longer functioning it became a very easy repair. I had the part in 2 days per the initial order information. Installation was merely insuring that each wire clip was connected in the EXACT location on the new Relay as on the old one; removing one at a time from the old to the new is key. This took all of 5 minutes at the most including replacing the front panel back on to the washer.

I removed the two mounting screws and pulled the harness through the opening unsnapped the sensor from the harness and installed the new sensor i didn't have to used the adapters the new sensor fitted

Remove old module and insert new one. Took longer to get out of box than to install.

Removed old filter and replaced with new.

I switched the oven sensor easily enough, but it did not remedy the problem, so we are in the process of replacing the oven since it's about 20 yrs. old.

Unplugged the range, removed screws holding the old sensor. When I pulled it out, the wire connecting to the sensor was completely broken through,therefore I could not just pull the wire to get to the connector. Unscrewed one side of back panel to access the connector. Pushed the connector and wire of the new sensor through the hole ( and behind the insulation), disconnected the old sensor and connected the new one. Re screwed the new connector in place plus rescrewed the back panel. Plugged the range in and - Viola! Everything now works like a charm and I have my oven back. Easy-Peasy. Oh - I am an older female with very limited DYI experience. I just saved myself $650.00!

Removed the two screws holding the sensor to the rear oven wall. pulled out sensor wire. It was caught on other wires behind the oven. removed the three screws holding the 8" inspection plate in the center of the rear panel. Carefully move the insulation and reach in to grasp the back end of the sensor wire. Once free from the snag it easily pulls out with the sensor just as stated in the video. using the appropriate adaptor it was easy to re-asseble and and attach to the oven wall. Replace the rear panel with the three screws and it was done

Replaced the thermostat according to existing videos and had to adjust the thermostat using instuctions in the user manual for model CWE4800ACB.

lifted the top center panel off removed old filter installed new easy peesy