JDB9910AWS Jenn-Air Dishwasher - Instructions

Inserted snap spray retainer through center of sprayer arm, snapped whole thing into place, and I was done!

I just followed the instructions and all went well

Took rack out of box, son removed water tower from old rack, put it on new rack, rolled new rack into dishwasher. Presto! Done!

I reversed the tub wheel, cut off the protruding flanges so that the end of the axel pin was exposed. Then using a small socket I placed a split washer over the end of the pin, used the socket to hold the washer in place and tapped it into place with a hammer. Note there is a grove around the circumference of the pin which holds the split washer. This locked the tub wheel onto the pin and it still rolled freely. Unconventional but it worked great.

Basket Replacement very simple just remove old and set new basket in place

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

We twisted the tower counter clockwise to remove from the old rack. It was a bit tight but came off quickly. Then inserting the tower into the new rack went very smoothly. That's all there was to it. The new rack did not have a place where I could attach the flip down shelf, but I rarely used it anyway. Love partselect. They helped me avoid buying a new dishwasher. Using Cascade pods, my dishwasher cleans like it is new and it is 25 years old!

Shut off the water and electric then removed the cover at the bottom then removed the water inlet valve and replaced it with the new one. Turned on water and electric. Replaced cover at bottom. Very easy and the part was shipped quickly. No problems and the dishwaser works great now!!

I simply looked at the other side (which was still functioning) and put the new one on but in reverse (left side/right side) I also was missing the end stop to the slide and simply popped that in and snapped closed. Two simple parts and 15 mins. solved a whole lot of aggrivation,
without any aggravation! wish I had found this site sooner!

my husband took the bottom rack out, unscrewed it where there were screws, lifted up the unscrewed part, took the filter out,cleaned out any gunk, replaced the filter put the part back on, rescrewed it, put the rack back in and it works much better.

First you must understand that the end cap is not a solid piece. The plastic facing you is wrapped over the piece behind it. The separation may be obscured by age. Wedge thin bladed screwdriver into the outside edge of end cap at the bid point, a sturdy hunting knife will probably work better. When you hit the seam, pry it apart and fold it back. Unwrap the part and repeat on other side. The dishracks will easily slide out and in.

We heard a horrible grinding noise just after starting the machine TWO DAYS before Christmas. On a whim, I disassembled the lower spray arm assembly right down to the wash impeller. I ran the dishwasher and heard no grinding noise, so I knew it wasn't a problem with the motor/bearings. After taking out the old parts, I noticed the discharge pump housing was in two pieces, and judging by the look of it and how those two pieces were fitting together, felt something must be wrong with them. I ordered a new discharge pump housing unit and a few extra parts just to be sure, and after 30 minute install of the new parts, the dishwasher is back to life. A $65 shot in the dark repair by a non-repairman vs. a new dishwasher... I'll take the shot in the dark. Thanks PartSelect!! I'm on to ordering a new utensil basket now!!

Excellent site. When the dishwasher started making a loud grinding sound, i thought "oh great -- now I'll have to buy a new one". After searching the internet (I just entered the model number of my Maytag dishwasher), Partsselect.com came up in the search results. I read several postings from previous customers which described the same problem I was having... followed their step-by-step instructions and was able to disassemble the lower washer arm and find the culprit -- a broken wash impeller. Ordered the parts, they arrived within a couple of days, spent 15 mins putting everything back together and I'm now good to go! THANKS PARTS SELECT!!!!! I owe somebody a free lunch!

Turn off the power supply to the appliance. There is wiring you could mess up if something goes wrong. Open the door. Remove the four (4) torx head stainless steel screws on each side of the interior door panel. (total of 8). Then remove the two (2) torx head stainless steel screws near the top of the door on either side of the latch. Before you pry the interior door panel off, have handy a non-metallic weight, such as a brick or heavy book.. When you pull the interior door panel loose, the weight difference will cause the springs to pull the door up and closed. The brick will hold it open while you replace the cheap plastic handle. Do not try to fully removal the interior door panel as there are electrical wires attached. Just lien the interior door panel up onto the lower dish tray. You will need a 5/16" hex nut driver to remove the two (2) screws that hold the plastic handle on. Then, just reverse the whole process.

Snapped old ones off and snapped new ones on.