JDB6510AWU Jenn-Air Dishwasher - Instructions

Dish rack not same as original. No raised section on right for drop down ledge. Also the old rack had a section for wide rim bowls. New one is for plates only. Otherwise it is OK

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

Very easy after watching the video. thanks

My husband does all the repair work himself so he tore it all apart but it's hard to find parts for a 23 year old machine. A store about an hour from our house said they had the part. When we got there it was the wrong impeller and it was going to be $30 to order it in. I got home on that Weds. nite ordered it and had the part 2 days later on that Friday.My husband had the part in and the dishwasher running within 20 minutes. Thrilled with the fast service from you and my husband :)

Unscrewed bottom panel. I could see right spring in proper position, left spring lying on floor, and broken linkage. Ordered part from partselect.com. To install, had to unscrew dishwasher attachment to counter, loosen leveling legs, pull it out a bit, then could replace linkage and reattach spring, retighten leveling legs, then push back in and replace screws and bottom panel.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.

The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.

Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.

We had tried to use dish washer cleaners, and they would work for a time, but we started spending more money on cleaner than we wanted. I ordered and then I replaced the lower spray arm. It took a little effort to get the top screw off, due to hard water deposits. The new one went on very easily, just screwed right in like the old one. It's working great and I really don't mind not getting a new one or paying for a service call!!!

Both racks are just roll out & roll new racks back in, no tools. Racks came in just 2 days, one was damaged in transit. Called to advise PartSelect of the problem. replacement rack was here within 2 days.
Great service. Jack

i removed the bottom spindle inside of the washer compartment. laid the pieces out in order of which they were removed. found the impeller was busted where it attaches to the shaft of the motor. screw was missing but found it laying in the bottom (there is a screen that filters the water as it drains). replaced impeller and put parts back together in order. good as new.

Removed the top rack and unscrewed the six screws involved on the rack adjuster. (Take note on how you took the thumb adjuster on top off for easier reassembly) Replace assembly on rack and slide rack back into dish washer. Kudos to PartSelect for getting my part here in less than 24 hours on a normal delivery charge.

removed motor pump assembly, worked my way down from the top, found problem ,ordered parts. put back together it was real easy,replaced back into unit. turned on water and power. runs perfectly.

received new basket without a basket handle; had to remove handle from old basket & attach it to new basket; took 2 separate tries to remove old handle & each try took about an hour; used screwdriver & pliers but had to be careful not to break handle; eventually used dimes to pry open & hold the attached sections of the handle open in order to free the handle from the old basket; we sure hope the new basket lasts a lot longer than the 2 years that the old basket lasted before it broke.

Simply had to replace the clips in the correct position. Would have been a five minute job if I had noticed which way around the old parts went before removing them from the dishwasher to find replacements. It's amazing hoe many permutations there were before it all fit together perfectly.

I recieved a different part than was in the picture and description that I ordered, and was billed twice for it. I wasn't able to fix my dishwasher