JDB3600AWP4 Jenn-Air Dishwasher - Instructions

Watch video and followed instructions. Very easy!

Nomenclature of parts were not named with a drawing, Photos of instructions were very dark and unable to ascertain which was which , they were worthless. It took me 20 minutes to figure out where the new parts belonged. Keep in mind the new parts were different than the old parts. A simple sketch would have helped a lot.

I ordered this thinking I would probably need more parts, but was unsure which ones. When the part arrived I immediately noticed that it was not identical to the original part, but looked like it may work. I also received an instruction book that I did not expect. The first side probably took 15 or more minutes. The second side was installed in just a couple minutes. The toughest part was removing the old pieces.

The repair was easy: just remove old assembly and replace with new one which was slightly different. The included directions were very poorly printed and practically useless so if you are not somewhat mechanically inclined it would be almost impossible to install just using the instructions provided

1) Pull out dishwasher from under counter. 2) Disconnect spring located at the bottom on each side of dishwasher. 3) Using socket remove pulley wheels from each side at bottom. 4) Install new pulleys on each side. 5) Wind pulley cord around both wheels and attach to one end of the spring on each side. 6) Using pliers extend other spring end to lower frame of dishwasher on each side. 7) Open and close dishwasher door to test. 8) Replacement complete

Followed the repair video supplied by the site

The parts seemed more sturdy than the originals that broke, so I hope this will be a better design. The instructions were adequate for installation and the adapter for the screws was supplied with the parts. The most difficult part was removing the old broken rack adjusters since there was no instruction for that.

Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!

removed front panel and pry switch from latch then remove two wires and reverse to install.

My wife hired a local repairman when the right side spring cable broke (I was out of town). He took two hours to fix it (and two appointments). The door would then pop open when running. He came back and replaced the latch. Problems persisted. I then ordered new hinges and replaced both in half hour or so. Would recommend doing all of these repairs yourself. None of these repairs are that hard and definitely not worth paying hundreds to do it. Trickiest part is pulling the dishwasher out from the counter without impacting the electrical or water connections. Disconnecting the power is important on all repairs. When you take the screws out of the door to get to the hinges, make sure you have a helper just to hold the door up while removing the last few screws. The left side hinge was really bent (when the right side spring cable broke) - caused the door to be out of square and thus would not effectively close. This was obvious after a 5 minute search on this this and other repair sites. Process that I used: 1. remove screws from both sides holding dishwasher into counter (may have screws into countertop as well). 2. turn off power, 3. pull out dishwasher far enough to see hinges and springs (careful of connections), 4. remove front door screws, 5. take off front panel, 6. remove spring cables (pull cable taut and remove "hook" from hinge)., 7. unscrew two screws holding hinge to door, 8. bend metal fingers around hinge pin to be able to remove hinge., 9. attach hinge in opposite path. 10. repeat on other side (if necessary), 11. reconnect things in opposite order...test door prior to reattaching door panel. Make sure you level the unit with the adjustable feet. Make sure screws in sides of cabinet aren't too tight as it can take the unit out of square pretty easily...

After replacing garbage disposal. I referred to you video you sent me when i received the new replacement hose. That made it look very easy to install. Thank you for all your help and support.

One Spring and both Balance Link Kits were broken. The repair itself was incredible easy, especially after watching the repair videos. Maybe 2 minutes per side. The moderately difficult part was removing the water supply and drain lines. Our dishwasher is some distance away from the kitchen sink. The supply and drain lines are routed behind and through some lower cabinets making reconnection a bear. Finally used a wire coat hanger as a guide and was able to re-thread the lines through the cabinets. The dishwasher could not be removed from its cabinet without first removing these lines.

Followed the YouTube video linked with the part ordered and it was an absolute dream

removed and installed cords with screw driver

The old filter simply unscrews and the new one screws in.