JCD2595WES00 Jenn-Air Refrigerator - Instructions

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

I removed the plastic portion to get to the switch and wires. I removed the old switch by disconnecting the two wires and pushing it out of its setting.

I discovered the old switch only had 2 prongs where the new switch had 3. Once I figured which 2 of the 3 prongs would light the lightbulb,
I then connected the two wires to the correct prongs of the new switch. I pushed the new switch into its setting and replaced the plastic portion on the refrigerator. Voila, success. The refrigerator door now comes on when its door is opened.

Thanks for the having the part and getting it at our door step in 3 days.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

I removed two small bolts that secure the flapper that keeps ice from falling out when you open the door, one bolt that holds a cosmetic cover for the wires and slid the icemanker forward. The only difficult part was removing the plug since it was high up, the wires were stiff and there's a release to push that locks the two plugs together. Once it was removed all was installed in the opposire order.
The part I ordered had a slightly taller channel where the water refills so I had to trim it to allow the new icemaker to slide in without bending the fill nozzle. Other than that it was pretty easy.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

change light bulbs

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

Replacement of parts was simple. But there are three main reasons that ice maker quits: door sensors stop working; ice maker, or it control system, stop working, or the coil controlling when water is released into the ice maker stops working. It was easy to replace the door senors; repairman replaced the ice maker and control board, which is located in one end of ice maker, but it ended up being the coil or simply a frozen water outlet into the ice maker that stopped the system from from working. The first thing you should do is to make sure that the water outlet into the icemaker is not frozen - use a hair dryer to melt frozen ice in the outlet - don't melt the plastic outlet with high heat. If the system still does not work go to this: look at red sensor on door to the the right. If it blinks twice in a couple of second with a time out and then repeats over and over, close the door on the receiving sensor on the left hand side of the casing and if the red light comes on steady then the sensor is working properly. So, now you have the coil that turns the water on and off or the water maker itself that can be bad. It will be one of these that are at fault, but not both. Call a repairman.

1. Tried to unscrew the bolt that held the broken coupling.
2. Had to have daughter hold on the plastic spinner on the other side so that the bolt would unscrew and not make the whole mechanism spin.
3. Screw came out.
4. Put coupling in place.
5. Put screw back in and tightened everything up.
Really easy, once the screw actually began coming out.

It was so easy. I had no idea. My husband and I were directed to your site and we ordered the part with scepticism but with hope that it would solve the problem. As soon as it came in, my husband installed it in five minutes. It was working immediately. Thank you.

Easy repair, unplug the fridge and then remove the 3 screws on each side of the freezer holding the emitter and receiver. Swap the boards and re-install. Takes less than 10 minutes.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

removed the LED covers on both sides of the freezer, unplugged each circuit board, plugged in both circuits, replaced the LED covers, job complete, making ice

First thought it might've been a problem with the inlet valve assembly but it wasn't. Took the factory unit out of the refrigerator and from testing found out one of the wires (black) was busted so splice a new wire in and motor started working but the "arm" would only rotate to a certain point and stop. I then discovered a broken tab inside the motor housing so at the point I just ordered a brand new icemaker unit. When I got it, I just mounted it to the base plate then slid it into the tracks in the refrigerator. The spout where the water comes out was the only tricky part but it is flexible so you just have to push it away and put it back into the tray when the whole unit is inserted. Once inserted, connect the power to the refrigerator, lock the wire cover to the base plate and you should be fine. The new unit started working right away. Whole process took 5 minutes.