J765303 General Electric Range - Instructions

Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.

First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

At 76 I no longer do my repairs so I asked my daughter's friend to do it for me.

The terminal blocks become brittle and carbonized with age resulting in very poor contact with the electric burners. The burners lose capacity to heat fully and eventually stop working.

Unplug the stove first! There is a risk of dangerous electrical shock if the power is not disconnected.

Repair involves removing the burner and the drip cup to expose the terminal block. Remove one screw on top to detach the block from the stove top. Remove the insulating cover and the clip that holds it in place on the back of the block. Detatch the two wires. At this point the age and brittleness of the blocks became apparent as they crumbled in my hand while removing the terminal screws. One screw had several layers of carbonization covering it and required needle nose pliers to get a firm grip in order to loosen it.

Inspect the wires to make sure there are no holes or cracks in the insulation.

Attach the wires to the new terminal block using the new screws provided. The new kit also included quick lock screw fastener clips to place over the holes in the stove top. It's a good idea to use these for more secure mounting and better grounding. Place the new terminal block under the stove top and mount it with the new screw provided. I had to unbend the mounting clip slightly to get it to fit, but it was easy enough to do with bare fingers.

Replace the drip pan and the burner. Plug the stove back in.

A pot of water now boils in under a minute compared to the 5 to 10 minutes it used to take.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

I couldn't find the oven model number so I just looked at the shapes from partselect.com. This would have been fine except I didn't know my Kenmore model had 4" leads so the one I ordered were only 2". I had to return the first element but the process to do this was FAST and EASY. With help I found the model number and had the correct part shipped. It took less than 5 minutes to install. It took longer to mop and clean behind the oven that hadn't seen the light of day in 10 years.

This range is about 30 years old and I was thrilled to still be able to get the bake element, which burned out about a month ago. I was doing research to buy a new stove when a cousin, from out of town, called to say they were going to visit the following week. No time now to get a new one installed. "partselect.com" was the fastest way. THANK YOU!

First off, I want you to know I'm an obese 56-year female without tools. But, I knew where to borrow those.

I first shut the power off to the range. I then disconnected the 2 screws that hold the element and pulled it out to reveal the 2 screws which connected the wires. I unscrewed those and removed the bake element. I double checked the stove model and bake element part # at the GE website and ordered it from "Partselect.com". It came in about 3 days. I then reversed the order of the above and it was done.

Here are some challenges I encountered..
1) The oven door was in the way making it uncomfortabe to get to the back of the stove.
2) Those $#%& screws are so short I kept dropping them.
3) The wires in the back bend easily. Be careful.

That's about it. It was a pill but not a real problem. It sure beat buying a new range before I've decided on which one to buy.

Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.

Unscrewed the 2 screws holding the old one in and the 2 bolts holding the bracket. Installed the new one in. 20 minutes.

Snapped in place (4)

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.

Identify oven breaker and turn off power before starting. Opened oven door. Removed oven racks. Use 1/4" socket or nut driver to remove the 2 bolts holding heating element mounting bracket at rear base of oven. Carefully pull element out of installation mount to remove the 2 machine screws that attach electrical wires to the heating element. Reattach wires in same order as original element. Then reinstall new element in reverse order of removal. Took all of maybe 15 minutes! Excellent OEM Parts!

My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!