J2B918SEK1SS General Electric Range - Instructions

Easily glide in.

The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!

There were two small screws at the back of the stove (this was the part that intimidated me. At first glance it doesn't look like it should be removed). But you just have to unscrew them, disconnect the wires behind them (this part can be done by hand), and pull the element out. The new element slides right in! Just make sure the power to the stove is disconnected either by breaker or by unplugging it. I'm not sure if it matters, but I made sure to connect the wires to the same side of the element that they were removed from.

Saw the brief video and as stated took less than five minutes to replace. It took longer to clean up the floor under the oven than to replace heating element.

replaced

I had to remove the back panel on the stove to free up taped wires to get more length.

Turned off circuit breaker, removed screws holding old element in with nut drivers, pulled out old element about 3-4" to reach terminals connected to back of element, removed spade lug terminals with needle nose pliers. Reconnected terminals to new element and screwed new element in place with nut drivers. Turned on circuit breaker and oven. New element works perfectly. Took about 8-10 minutes. Very easy to do.

ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking

I opened oven and pushed oven rack inside.

Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's that easy. No more f2 been working like a champ!!!

Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the replacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."

Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.

Followed the instructions that were sent to me by E-Mail.

This part is a PC Board. Step 1 - pull the oven away from the wall far enough to permit access to the back. Step 2 - Unplug the oven. Be careful of the gas supply line. Step 3 - Before touching the new part, wear a "grounding strap." Step 4 - Using a "Phillips" screwdriver remove the four screws that connect the top cover plate that covers the control assembly. Once the screws are removed the top of the cover will need to be rotated a bit to the rear to remove it from the oven. Step 5 - Carefully remove the ribbon wire by gently grasping the locking bar tabs with a thumb and forefinger and pulling back until the ribbon wire slides out. DO NOT use any force here. Gently move the ribbon wire out of the way being careful to make no crimps in it. Step 6 - Using a magnetized "Phillips" screwdriver remove the four screws holding the oven control assembly to the oven. Carefully remove the foam insulator connected to the bottom two screws. Step 7 - Locate the new oven control assembly above the old assembly and begin transferring the wires, one at a time. Care here is needed as the connectors are tight. Grasp the connector with your fingers and pull straight back. DO NOT pull the wire. Step 8 - Once all wires are transferred dispose of the old oven control assemble and screw the new assembly back on to the stove. Use a magnetized "Phillips" screwdriver. Insure the foam insulator is attached to the bottom two screws in the appropriate holes. Step 9 - Once the oven control panel is secured, insert the ribbon wire carefully and close the locking tab. Step 10 - Install the top cover. Make sure the bottom lip is under the foam insulator and that all wires are clear and free before pushing it tight to the stove. Replace the fastening screws. Step 11 - plug-in the stove and insure all oven functions work correctly. Push the stove back into place.

Would have been easy, but I should have checked the measurements more carefully as it didn't fit. But the service from Part Select has been excellent!