Models > HDA2100R20BB > Instructions

HDA2100R20BB Hotpoint Dishwasher - Instructions

All Instructions for the HDA2100R20BB
121 - 135 of 287
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Water not pumping out of tub.
Repair was easy. However, this did not solve the problem.
Parts Used:
Drain Solenoid and Bracket Assembly
  • Ray from LOUISVILLE, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher leaking
I simply lifted the baffles out and cleaned the base and installed the new baffles and started the dishwasher and NO LEAKS.
Parts Used:
Corner Tub Baffle - Lower Left Corner Tub Baffle - Lower Right
  • Larry from JOLIET, IL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
NEEDED TO REPLACE LOWER RACK IN DISHWASHER TO SELL HOUSE
TOOK THE RACK OUT OF THE BOX AND PLACED IT IN THE DISHWASHER, DONE.
Parts Used:
LOWER RACK
  • Elizabeth from JONESBOROUGH, TN
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rack slide end cap broke
Slide it into the arm until you hear it snap
Parts Used:
RACK SLIDE END CAP
  • john from SOUTHPORT, NC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking from the corner of the door
Replaced the lower right and lower left corner tub baffles
Parts Used:
Corner Tub Baffle - Lower Left Corner Tub Baffle - Lower Right
  • garrett from OROVILLE, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The covering over the original dishracks had worn away and the framework beneath was rusting.
The only trick was the endcaps, which were not intuitive. I followed the instructions in the following Youtube video , which direct the user to bend a tab at the rear of the endcap back away from the front using a quarter in order to allow the endcap to rotate out of position inwards into the interior of the dishwasher. The old racks then slid easily out of the dishwasher, the new ones equally easily slid in, and then the endcaps required the tab to be bent back to allow them to rotate back into position.
Parts Used:
LOWER RACK UPPER RACK
  • Douglas from WOODBURY, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rear 1/2" wheels on new rack were too narrow causing rack to fall off tracks
Removed 3/4" rear wheels from old damaged rack and installed them on new rack. Works fine now. For the price paid for this replacement rack, wide wheels should be included as part of the replacement package.
Parts Used:
LOWER RACK
  • David from EDEN PRAIRIE, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Threads on the cap broken
A no brainer, replaced old fill cap with new fill cap. Delighted I was able to order the part, website is user friendly.
Parts Used:
Rinse Aid Fill Cap
  • Martie from FULTON, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to dishwasher
Replace both micro switches.
Parts Used:
Interlock Switch
  • Robert from OLD TOWN, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking valve
Used teflon tape around new 3/8 elbow. Re-installed valve in originals postion. Connected supply hose and reconnected electrical to valve.
Parts Used:
Water Inlet Valve
  • Gary from HAVERHILL, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wires wee very rusted and some almosth rusted through.
The lower dishrack just lifted out and the new one placed in. The upper rack had stops at the end of the slides which could be removed with the help of a flat blade screw driver, old rack slipped out, new rack slipped in and the stops replaced on the end of the slide which keeps that upper rack from coming al the way out of the dishwasher. There was a link to a "how to do video" on the email order confirmation. It just gave me reassurance that I could easily do the job.
Parts Used:
LOWER RACK UPPER RACK
  • Roy from TUCSON, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
valve leaked
shut off water. removed lower panel disconnected power removed supply hose and outlet hose. disconnected electrical plug from valve. Un bolted valve from frame. removed elbow from valve inlet. installed elbow on new valve using Teflon tape. reinstalled valve to frame. connect hoses + electric plug to new valve. turn water on check for leaks. reconnect power. run dish washer check for leaks & popper operation. reinstall lower panel.
Parts Used:
Water Inlet Valve
  • Paul from KENT, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Racked rusted out
Simply removed the old rack and installed the new rack.....easy as 123 ABC. Dishwasher still works fine but the bottom rack had rusted out. Not sure if this is common for this Hotpoint dishwasher as my deciding factor to order from here was that others had the same problem as me.
Parts Used:
LOWER RACK
  • Brenda from PLANO, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dislodged & deformed baffle leaked after 29 years of use
I lifted out the old baffles, cleaned the soap scum from the recesses, and placed the new baffles in by hand. No tools were required, and total repair time was less than 8 minutes. the total cost was a fraction of the cost of a service call.
Parts Used:
Corner Tub Baffle - Lower Left Corner Tub Baffle - Lower Right
  • MAX E. from CALDWELL, ID
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leak
Replaced both corner tub baffles but did not correct the problem.
Parts Used:
Corner Tub Baffle - Lower Left Corner Tub Baffle - Lower Right
  • Jack from JASPER, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the HDA2100R20BB
121 - 135 of 287
Back to Top