Models > GTWN5650F2WS > Instructions

GTWN5650F2WS General Electric Washer - Instructions

All Instructions for the GTWN5650F2WS
106 - 120 of 202
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken straps
replaces as per video. Very helpful
Parts Used:
Tub Dampening Strap
  • Roger from ORO VALLEY, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaceed agitator
Old agitator was stuck on and i could not pull it of.I used two claw hammers and put the claw under the agitator and broke it free.Worked perfect" Took five minutes "
Parts Used:
Dual Action Agitator
  • stanley from Pownal, VT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not completely drain all the water out of the tub after the final rinse cycle, with a burning smell from the belt because it could not turn properly.
I followed previous parts select customers advice exactly, of replacing the dampening straps, and it worked perfectly. Thanks-A-Million!
Parts Used:
Tub Dampening Strap
  • William from Cumberland, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old drain hose was cracked
old one out, new one in. new one is seated, but not a perfect match bracket to hold hose in washer does not fit on this replacement hose properly. But I feel comfortable with the result & use
Parts Used:
Drain Hose
  • Dirk from State College, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
cracked drain pipe
Remove two bracket screws. Removed hose. Put new hose in place using same bracket and screws. inserted end of hose into washer drain. Secured hose to cold water hose with two zip ties.
Parts Used:
Drain Hose
  • Belinda from FLORENCE, KY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator was broken
First tried pulling the old agitator out by hand but couldn't get my fingers under it to pull upward. Tried several times but no success. Finally put two metal rods about 8 inches long in the holes in the bottom of the agitator and used them to lift upward, it came up immediately. I then pushed the new agitator down into the slot and it was finished. There is always a way when you think about it.you are a winner.
Parts Used:
Dual Action Agitator
  • Mabry from CLINTON, MS
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
New Washer purchased, not having a Fabric Dispenser
Pulled cap off on top of the agitator, slipped on the fabric softener dispenser & Boom ! User friendly website in ordering this part along with quick delivery, thanks!:)
Parts Used:
Fabric Softener Dispenser
  • Glenn from PLANO, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
AGITATOR BROKE
pulled up on agitator and it came off and replaced it with the new one
Parts Used:
Dual Action Agitator
  • tiberiu from CLEVELAND, OH
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tube Shaking Like Out Of Balance. Water Not Draining Completely And Created An Unpleasant Odor
Main thing is watch the video. It may vary a little according to the age of your appliance, as it did with me but common sense guides. The difference was minor on my part. Two hex head screws to remove per strap and they had to make them 1 size different. Go figure. Have your change handy. A ratchet nut driver will save you some time.
Parts Used:
Tub Dampening Strap
  • Arlis from Moore, SC
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced leaky tubseal
Repair went great. The large nut had to be soaked to free it but the part was an exact fit.
Parts Used:
Tub Seal
  • Michael from Hollywood, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
3 of the 4 dampening straps were broken.
Watched the video from your web site and followed the instructions. Didn't need to remove the console on my model.
Parts Used:
Tub Dampening Strap
  • Walter from woodland, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer noisy and leaking
Repair was done with the help of step by step insructions available on utube, just enter model# and the repair you need to do. One problem I had was new tub seal{GE part] was a little smaller in diamater than the seal I removed And still leaked when I first ran washer So I took it back out and used a sealer [Permatex Indian Head gasket shellac compound from auto parts store] as recommended by one of the the repair techs on utube and it sealed it perfectly, just let it set op for about three hours and nice and dry now
Parts Used:
Tub Bearing Tub Bearing Washer Tub Seal
  • Don from Milford, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken tub strap
follow youtube vid. simple
Parts Used:
Tub Dampening Strap
  • larry from Steamboat Springs, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken dampening strap
Watched the video, read installation instructions.
Replaced four broken dampening straps, washer is quiet and all is good.
Parts Used:
Tub Dampening Strap
  • Priscilla from Beverly, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
had a pin hole in the drain pipe
order the part and replaced it and it works just great! May I add never before have I had such an amazing experience in dealing with your company, your company shows pictures and I ordered the part in the late afternoon and I had it the next day, the diagram you show on your site was so helpful, you told us that the part now is replaced with a different #. Once again KUDOS!! to your co.
Parts Used:
Pump to Tub Inlet Drain Hose
  • ROBERT from Bynum, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GTWN5650F2WS
106 - 120 of 202
Back to Top