GSS26C5XXW03 Whirlpool Refrigerator - Instructions

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

I use a Screw drive a Nutdriver set Needlenose Pliers and it took 30mins to fix.

I spent several hours defrosting the unit. Making sure the vents were all defrosted and free of ice. The part replacement is fairly straight forward; remove the thermostat, cut two wires, reconnect the wires following color codes, attach to coil and restart. And, "Yippie!". Nothing. Zilch. Zero. Because I could not connect with the online repairman, I spent 40 bucks for nothing; problem was not resolved. Thanks for taking my money. I'm bummed and with just a little less money in my pocket. Never again will I ever purchase another Whirlpool product. Or buy from your outfit again (because of the over priced part). I replaced a 25 year old 'working' General Electric fridge for this junk that sat in the warehouse for four years before this was delivered to me in 2018 and sold to me as a "new" appliance. This was found out only when it crapped out and I needed to have it checked out for repair. Oh yea, I only had the comment section and the part recommendation to go by, and the latest comments are at least two years old. I'll be surprised if this even gets posted.

Removed old filter then insert new filter and pushed door closed

1. Removed 2 screws on top hing.
2. Easily lifted door and place on table.
3. Removed set screw for door cam.
4. Removed stop bracket.
5. Reversed steps 4 thru 1.

When tightening top 2 screws, make sure door gap is consistent and top of frig door aligns with the top of the freezer door.

NOTE: The lady at PartSelect who helped me with my order was great. Took the time to verify my parts. Prior to this I had bought the part from a nearby appliance parts store. They sold me the wrong part, even though I showed them a picture of my model number plate b4 ordering. In the future, I will always go to PartSelect for my appliance part purchases.

Line up door handle, insert Allen wrench and tighten.

shook bottle and painted waited a day and repeated

Removed the cover to ice maker. Removed with 1/4 inch socket and the extension, the 2 Nutscrews holding the ice unit in place by bending down the plastic cross piece in front of the screws. Finally squeezing the electrical cover case to remove from the rear wall to get to the Electrical plug connection. Once cover away from the wall and new plug connected, the new ice maker was hung onto the upper slots and nut screws re-installed, again by bending the plastic cross piece for ease of securing the unit. Re-installed the cover and turned the unit on - it made ice like when the refrigerator was new.

At first ordered the wrong part. Using the website was difficult to find the correct part, but once I called, it was pretty easy to find the part needed. Part showed up and install was only a few minutes. No more leaking!

Thanks for the help PartSelect!

Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.

1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove two mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.

bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what is inside the refer!

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.