GSE25GYPFCFS General Electric Refrigerator - Instructions

replacement part was not identical to the original. Mounting screw sockets did not exist on replacement part. I still used the new part but it is held in place by gravity (no screws). New part works but must be treated gently or will break like the original or fall out of place. Part diagrams online were not adequately clear. It would have been good if photos existed of the replacement from assorted angles, and I would have seen the lack of mounting screw sockets.

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

Changing out solenoid was very easy, but you don't have to remove trim ring and it didn't fix my problem. Turns out a relay fell out of its holder in the piece you have after removing the 4 screws per the video.

YOU SENT THE WRONG PART AFTER I SPECIFICALLY DESCRIBED IT AND SAID, NOT THE SMALL PART FOR THE BOTTOM, THE LARGE ONE FOR THE MIDFLE. THEN YOU MADE ME PAY DELIVERY CHARGES TO SEND IT BACK.

We opened the box, unpacked the drawer, washed and dried it, installed it! No muss, no fuss!

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

Installing the part repaired the fridge and freezer immediately.

Followed steps found on YouTube. The only missing instruction was to remove the small retaining clip from the water tube inlets to allow you to press the retaining circle down to release the tube

I watched the video a couple of times and followed the instructions exactly and the repair was very simple. This repair took me a bit more time than I thought it would just because I followed the steps methodically.

But the video was perfect to guide me through the procedure to replace this part. One of the longest parts was removing the shelving and food storage bins, cleaning them, drying them and then putting them back in after the tank was installed.

In preparation, I removed the bottom crispers and shelf to clear space, and removed the hood and items above the tank near the light. You'll need to also move the fridge away from the wall to access the back. Installation seemed very easy - two screws holding the tank itself, one hose to the water supply in the back, and another to the bottom of the freezer door to dispense. Then the hard part started after it was installed. First, I could hear the click but no water was coming out. After several views of youtube videos, I realized there was a plug in the hose to the supply side. Duh! So now I had water, but also a slow drip when drawing water. I believe the issue was that I was not pushing the hose on firmly enough, and eventually I got it right. Also, you need to understand the connector: there is a little ring around the place the hose fits; pushing it TOWARD the housing releases the hose, and pulling it back AWAY locks the hose it place. That was not clear to me without watching a youtube video.

The door stop is held by 2 TORX screws and can be removed in place without raising the refrigerator. The only tricky part is that you only have about 2 inches of clearance so it is hard to locate/see the screw heads. I used a small mirror to help me align the tool with the screw. If you have a small ratchet with a TORX socket it will make your installation go much faster. Each turn of the tool required me to remove and reinsert the tool. This is what takes up so much time.

I put kickplate on refrigerator and use 2 sheetrock screws and drill to attach. Done in 5 minutes.

I went to the internet and found parts select web site. Saw all of the possible fixes for my problem and read all of the other repair stories. My story actually became a journey that is still continuing. I first changed the water filter, but still no water at the dispenser. I next disconnected the coupling at the bottom of the freezer door that carries water to the dispenser and when the dispenser was depressed, water flowed at the coupling, but not at the dispenser. After reconnecting the coupling, I turned the freezer setting to 1 for 4-5 days, but still no water at the dispenser (possibly the line was frozen, but we had recently been away for a week and the water dispenser still supplied water at a freezer setting of 4). Now I am at the point of the journey into replacing parts one at a time to get water. First I ordered the dual water valve for the ice maker and water dispenser. I replaced this valve with instructions from Parts Select and still no water at dispenser. Next I ordered and replaced the switch at the dispenser lever and still no water. Next was the solenoid attached to the ice door, ordered, replaced and still no water at dispenser. I am now at the final part in this repair and that is the $132 circuit board. So I will be ordering this part soon and hopefully that will fix the issue.

FOLLOW INSTRUCTIONS OF YOUR VIDEO

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.