GSD4000JB General Electric Dishwasher - Instructions

I removed the front bottom panels to give me access to the Solenoid area. I did not take out the dishwasher from the cabinetry. I removed the screws holding the solenoid assembly and the C clip holding the hand fan shaped white nylon thing onto the valve shaft. I slipped these to the side. Then I cut through and removed the push on nut with a wire snipper plier. Then I used a knife blade tip to pick out the black seal. I then slipped the new seal onto the shaft, being careful that the flat side was outward, and slid it down the shaft and , with my fingernail, pushed it completely flush into position. The biggest challenge was the push on nut. It does not push on easily and must have the lips pointed outward. It required the use of a 3/8" diamater tube slipped over the shaft to tap the nut down the shaft. This caused the shaft to push into the pump housing, which caused the valve to bind. So I used a vice grip to pull out on and hold the shaft while I tapped the push on nut with a flat head screwdriver. Then I just reversed the solenoid assembly removal. But , when I ran the dishwasher, it no longer leaked.

Opened the package and screwed in the new rinse aid fill cap. No problems. It fit and works just fine.

Just took the old rusty rack out and put the new one in its place.

I pulled the dishwasher out from under the counter. Loosened the collar holding the sump housing to the pump motor. Unscrewed the cover inside the base of dishwasher to release the collection opening of the sump. It's very flexible so I pulled it out by hand. Put the new one in and screwed everything back down. Pushed the dishwasher back under the counter. Simple Simple Simple.

Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.

Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip. , Rescrewed in the new rubber connector. ( Hint- used petrolem vasaline on the rubber connector base for a water tight fit) . Reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. Turned water back on. All worked at well.

Unscrewed 2 screws from under the counter, pulled out dishwasher. Saw where it was leaking. Took wires loose, took the rack out, unscrew the white mesh, took out the dishwasher sump housing product saw a crack and ordered the piece. For anyone out there make sure you turn the electric power switch off before you attempt to fix anything!!!!!!

Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.

My son found a water leak and cut the water supply off. He then pulled the machine from under the counter at which time I examined the valve under pressure and saw the leak. We cut the water off again and after tripping the circuit breaker we pulled the electrical connector and undid the mounting bracket which made getting the lines off the valve much simpler. New valve in hand I attached the lines and did a test then remounted the bracket and attached the electric. Easy as pie!

It was tricky to get the old rack off. Usually you can unclip the clips closest to the front wheels to pull the rack out. However, there is an area behind one of the wheels that you can kind of release and than pull the rack out. You then have to slide out the funnel/fan piece from the middle. That piece slides/ snaps in the middle of the the new rack. Then slide the new rack in place, re attach the release used to slide oldrack out.
That is it !!

To remove the upper rack, twist the support rail end caps toward the center of the machine and slightly downward. The caps will come off and you can slide the new rack into place. Reverse the process to replace the end caps. One of mine broke and I will need to order replacements.
The original rack is no longer available. The replacement, which is the only one GE offers, has less storage space and is not as sturdy. It bends downward when full. I am very disappointed and recommend not replacing the rack unless you have no other choice.

First I looked for blockage and found none.I took the pump off and hooked power to it in my work shop and it did spin when powered up.We had broken a glass in the washer and thats when the problem started. I did find a few small pieces in the check valve assembly. It did not look bad but for cheap I ordered the part. Ran the washer and it drained on the wash but not on the final. Turned off the power.Slid the wash out where I could get to the power and not unhook the water. Turning off the power I disconnected the wires and carefully turned the power on and touched them to the pump and forced it to drain knowing that the pump worked I thought it would at least empty the water. I touched the wires to the pump and the board clicked the water drained. Hooked it back up. Ran it and has been working great since.

At first I found some water on my hardwood floor by the dishwasher, I thought that I might spilled't the day before, then it hapened again, so I remover the front lower cover for the dishwasher and I found water under the dishwasher, then I turned on the machine and I found a pin hall water leak from the water inlet valve. I turned the machine off, then I closed the water valve under the sink, then I disconected the power plug from the valve, the diconected the water supply copper pipe, then diconected the house from the valve to dishwasher, then got the part# from the valve sticker and the model# for the dishwasher from inside of the door. after that I went online and I got the valve. make sure to try more than one website because they all have differant prices, and Parts Select was the lowest one.

with electric power and water source turned off,I first bailed out the water from tub then I pulled dishwasher out from under cabinet . Then I removed the motor and pump and put it on the table. I took a digital photo so I could remember exactly how everything was assembled. I checked for clogs and damage and realized that the solonoid casing had melted around the armature link assembly . I Looked at diagram for parts name and number and ordered from parts select. In the meantime I put a temporary one feed valve on hot water feed line so I could have access to hot water in kitchen while I waited for parts wich were here in a couple of days. Put it all back and it runs fine. Thank for your help

I removed the scews holding the inside door to the outside door section. Once removed I removed the 2 screws that held the switch to the door. After removing this switch I had to open it up to expose the four wires on the switch. I reattached the four wires to the new switch closed it up and placed it on the door with the 2 screws.
Replaced the inside door. Job finished with the switch working and the dishwasher operating as per the factory standards.
Very easy job and by doing it myself I saved money on a service call.