Models > GLD5600NC > Instructions

GLD5600NC General Electric Dishwasher - Instructions

All Instructions for the GLD5600NC
106 - 120 of 238
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Leaking at the valve
Just like the video and replaced it
Parts Used:
Water Inlet Valve
  • Brian from DERRY, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Wrench (Adjustable), Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hinge arm link wore out
Used Phillips screwdriver to undo brackets that keep dishwasher in place. Pulled out dishwasher from underneath the counter. Placed hinge arm in spring, hooked spring onto clip, placed hinge arm in clip. Put back dishwasher under the counter and screwed in place. Took all of 15 minutes. Saved 185.00 for service call.
Parts Used:
Hinge Arm Link
  • Samuel from LAS VEGAS, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking hose
You tube
Just mack sure the electric is off - breaker and live wire check pre starting
Parts Used:
CLAMP Adaptor Pump Assembly Inlet Sump CLAMP
  • JANET from SANDY SPRING, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken silverware basket
Pulled the old one out and placed the new one right into place
Parts Used:
Silverware Basket with Lids
  • Alan from MECHANICSVLLE, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Our dishwasher lower arm had become clogged
HAHA! The easiest repair we have ever done! Took it out of the box, snapped the old arm loose, put the new arm in and -- the dishwasher works like new! Thank you!
Parts Used:
Lower Spray Arm - Gray
  • M Anne from VIENNA, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaked front right side
Followed the instructions that came with the my order
Parts Used:
Tub Gasket
  • robert from HAYMARKET, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
frost build up
flapper then bought the spring
Parts Used:
Recess Door Spring
  • JOHNNY from FORT WORTH, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would only drain intermittenly
Thought it might be check flapper valve on drain pump, so I replaced fairly easily, per instructions. When doing, I noticed the attached relay wires were not secure. When it was on the drain cycle one of the relay wires vibrated badly and loosened the connection enough to only work occasionaly. Would like to put new relay on the pump but they do not sell separately from the pump. (one assembly). I resecured connection and will wait till relay gives out and buy new assembly, but for now it's working perfectly!
Parts Used:
Check Valve Flapper
  • C. from Lexington, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Difficult to install the mounting screws
Nut driver and philips screwdriver.
Parts Used:
Water Inlet Valve
  • Edward from TUCKAHOE, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No water in
Pulled washer out. Found water inlet valve in lower left. Shut off power and water. Replaced valve with new.
Parts Used:
Water Inlet Valve
  • Everett from FREDERICKSBRG, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bottom door seal had crumbled with age
Removed inside of door, slide bottom seal on and put inside door back on. Job done!
Parts Used:
Short Bottom Door Seal
  • Dorothy from LAKE WALES, FL
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heat shield on lower spray arm came loose and blocked spray arm from turning
Followed instructions on how-to video on website on how to remove and replace lower spray arm.
Parts Used:
Lower Spray Arm - Gray
  • Jack D from CLEBURNE, TX
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dish Washer not cleaning well, spray arms not turning much all ttree had mineral build-up and even trash in them.
Ordered and replaced all three spray arms. The upper and middle spray arms were quickly replaced with a net-driver and are now working much better. The lower spray arm required no tool, just turn it CCW and lift it up. After replacement lower spray arm is still not moving at all. Maybe the lower spray arm washer is defective or the pump is just not putting out enough water. Will consider further repairs or replacement of the dish washer, it is 13 years old and used daily.
Parts Used:
Lower Spray Arm - Gray ARM SPRAY UPPER Assembly Middle Spray Arm
  • Roger from SADDLEBROOKE, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishrack was worn and causing chips on dishes
just slid the new rack into place
Parts Used:
Dishwasher Lower Dish Rack with Wheels - Gray
  • Kathleen from LOUISVILLE, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wheels kept coming off of the basket
Just remove the lower basket from the machine and pull the old wheels off. Then snap on the new wheels on the pegs. The old style wheels snap in place without much force. The new wheels take much more force to install and lock onto the basket which keeps them from coming off when the basket is heavily loaded.
Parts Used:
Lower Rack Wheel Kit - 8 Pack
  • Alfred from Aurora, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GLD5600NC
106 - 120 of 238
Back to Top