GHW9250ML1 Whirlpool Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Displayed F and H alternately
Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem
Parts Used:
-
LAVERNE from NIANTIC, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not operate, water in drum would not drain. Error code indicated a bad pump
Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately $150.00 bucks in repair service fees.
Parts Used:
-
Patrick from Beaumont, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken lock needed replacement
The best way to do it is not the way I started.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old lock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old lock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.
Parts Used:
-
Alexander from Miami, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Socket set
10 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tub would not drain even though pump was running
Remove three screws holding the lower panel, the pump is right up front. Probably the hardest part was holding the hose clamps open while attaching the hoses to the pump housing. One screw holds the pump assembly in place. Hold the over-ride switch closed, check for leaks, and replace the loser panel.
Parts Used:
-
Steve from Cary, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken timer knob
Was very simple repair, and just required pushing the new knob on by hand pressure. The part was ordered and it was delivered in two days, and I will not hesitate to order from this company again
Parts Used:
-
John from Yorba Linda, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
10 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washing Machine Filled with Water When Off
Turned off the water and unplugged the machine
Took off the top of the washing machine by removing three screws along the back side
Removed the hoses connected to the water inlet valve
Removed the hose coming out of the water inlet valve
Marked the 4 electrical connectors
Used plyers to pull the electrical connectors off. Needed to just pull hard. Won't break them off.
Remove the screw that connects the valve to the back of the appliance.
I confirmed this was the part causing the problem by blowing air through it with my mouth. I could tell that the hot water side was not closing all the way.
To replace the part, just repeat the steps above in reverse.
Took off the top of the washing machine by removing three screws along the back side
Removed the hoses connected to the water inlet valve
Removed the hose coming out of the water inlet valve
Marked the 4 electrical connectors
Used plyers to pull the electrical connectors off. Needed to just pull hard. Won't break them off.
Remove the screw that connects the valve to the back of the appliance.
I confirmed this was the part causing the problem by blowing air through it with my mouth. I could tell that the hot water side was not closing all the way.
To replace the part, just repeat the steps above in reverse.
Parts Used:
-
James from Naperville, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door latch error code
removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you
plug in three plugs ...works great
Thank you
Parts Used:
-
Gary from Sonoma, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
10 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old bellow pulled loose and torn
Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over the retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.
Parts Used:
-
RICHARD from Portland, OR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Parts Used:
-
Howard from Boynton Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
22 of 53 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The washer was unable to run without door locking
Removed the washer tub gasket and then removed the door part that I order . It was real easy to replace it and the tub gasket . Took about 8 min to complete everything .
Parts Used:
-
MICHAEL from DERIDDER, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door would not open.
It takes 2 people to do this repair.The bellow is the hardest part. One person has to hold the bellow in one spot, and the other person has to put it on the rim of the drum all the way around. Sort of like putting a tire on a bicycle. Dont do what I did and pry the door open. If you do that you will have to get a new door lock control at $54.Take off the lower front panel and reach up to the manual releace tab on the right side and pull down. Please make sure that the power is turned off, unplug the washer from the wall for your safety. The door switch itself is easy to replace, 3 screws, 3 plugs. Hope this helps.
Parts Used:
-
MIKE from LONGWOOD, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
9 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clothes came out dripping wet
Just removed the bottom cover to access the water pump. Drained the water through the filter housing. One screw and two hose clamps and the pump was out. Installed new pump and checked for leaks. None found so the cover was secured in plase. Great news, WIFE is happy.
Parts Used:
-
Louis from Branford, CT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The knob that controls the wash setting broke
It only took a few seconds to slide on the new knob after it arrived by UPS. The part arrived sooner than scheduled. Great service and product.
Parts Used:
-
Richard from Tempe, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Shaft in water pump broke
I removed the one screw that holds pun
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.
mp in place. I pulled to the left and foward about an inch to remove hoses and unplug wire. then pulled pump assembly out. The new one went right in. The wire plug went right in without any customizing. I think this was about as easy as it gets.
Parts Used:
-
Jeffrey from Adrian, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Control Knob Broke
I removed the old control knob by pulling it off and installed the new one. Your service was great!
Parts Used:
-
Bill from Chanute, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!