GCE23XGBBFLS General Electric Refrigerator - Instructions

Nothing to tell it was just a replacement part that the old part was removed and the new one inserted. Works like a dream Thanks

Cut out cracked tubing between valve and where tubing enters into refrigerator. Cut new tubing to length and attach to existing using union.

There are three holes under the front panel in which you push a very small screwdriver in and the front panel comes off.In back of the panel is another panel with 4 screws .1 at each corner.Remove the 4 screws and that will come off exposing the working parts that need to be replaced.This is also a good time to clean anything you can get to in that area.It is very important to remember how everything came out.

Removed the lower 2 drawers, lower front grill, rear lower compressor cover. Removed the 2 water lines from the quick connects and screws from the water tank. Pulled lines through the hole in the right rear of the refrigerator and removed tank. Then reversed steps to install new tank. The upper plastic tank cover has 2 buttons on top that are really screws with a plastic cap, these are easily removed with pliers.

Followed instruction video. Replaced water tank, flushed line from house water. Reconnected line and cycled until tank filled. I have ice and water now.

First:
Remove all shelf’s and drawers from fridge inside that were on the way of the water tank
Second:
Pull the fridge from the wall
Turn off the water supply:
Unplugged the power supply
Third:
Remove the cardboard cover at bottom of the fridge on the back for better access to the water pipes
From the front remove the toe kick for better access at the water pipes
Disconnected the water pipe at the front left side, use a rag or paper towel to hold the water that may drip ( bigger pipe)
Remove the covers on the top of the water tank inside the fridge
Disconnected the water pipe at the back left side ( smaller pipe)
Unscrew the water tank (two screws)
Pull the water tank out with the water pipes attached
Fourth:
Install the new water tank assembly , make sure the pipes goes on the hole at the right side and reaches the from and back
Connect pipes until the line that shows on the pipes
Screw back the new water tank
Put the protections back on the top
Plug the fridge and open the water supply to make sure there is no water leaks
The water is ready to be use

I took out the old bins just as when you take them out to clean them. And then I replaced the bins with the new ones.

It was much easier than I had anticipated it was going 2B. All it intaled was 2 undue the 2 water lines w/a 1/2 inch wrench, take out the 2 screws on the top of the head on the inside of the refrigerator, then pull it out. I then just slipped the new head in, replaced the 2 screws, replaced the filter (definitely not overly tightening it this time) by putting some waterproof food grade grease, making it much easier 2 push up & turn. After, I went 2 the back of the refrigerator & reconnected the 1 line 2 the fridge & then the other 2 the water supply. "Walla" we were making ice again & able 2 get ice cold water again, also. The entire process took approximately 30 minutes 2 complete & that's bcuz of my limited disabilities. A younger person could probably be able 2 do it possibly faster.

Replace the motor fan on condenser and clean the condenser

1. Emptied the crisper pan,
2. Removed it from the refrigerator,
3. Flipped it upside down,
4. Removed the old one by pulling it off,
5. Replaced it with the new OEM part. and
6. Reversed the process.

I had some trouble removing the broken switch because a lot of the frame was missing due to the damage from the dropped can. I tried a screwdriver first and then switched to a small putty knife, which someone else had suggested.
Once the switch was loose and wires were accessible, I also had some trouble disconnecting them but they finally turned loose. After that the new switch was easily connected and popped back into the opening.
Definitely take photos as you disconnect!

1. I unplugged the refrigerator/ freezer
2. Turned off water supply
3. Removed the screws that held the cardboard skirt in place
4. Unplugged the water tube from the push connect
5. Removed the screws around the water inlet to the ice maker
6. Remove the water fill tube
7. Install new water fill tube and put all the screws and plates back where they go

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

after replacing the door seal, I couldn't get the new seal to close and stay closed, so I replaced the closing arm and spring. The door will close now but not tightly and it's loosing cold air. So I made and patented a wooden block to put behind the freezer door handle and the refrigerator door handle to keep the doors closed. Available in black, white and natural tan. (just kidding about the patented part, but not the block)

I replaced the three sensors, 2 in the freezer 1 in the refrigerator. This was rated as the most common problem. Did not fix the problem. I then checked the ohms on the new sensors then the old sensors they were all within .5 of each other. So I got smart and went down the list of causes on their list. I emailed partselect and asked what the parts should read. They replied with that information and it turned out to be the voltage converter on the compressor. I ordered the part on friday payed for overnight delivery and it arrived tuesday. This as you can imagine makes me angry. But the part was easy to install and my refrigerator started working right away. I would advise anyone with this problem to start at the top of the problem list use a multi meter check everything on the list and only replace part or parts that don't come up to standards. This will save time and money and hopefully fix the problem the first time as you are not switching out parts and hoping that it solves the problem.