FFHN2750TS1 Frigidaire - Instructions

Water was leaking so I replaced the entire valve and just followed the color codes and thats it. Plug and play.

Removed lower cardboard cover, shut off water supply valve, unpluged frig. Used wrench to remove 3/8 water line from water valve, removed electrical connectors from solenoids, used fingers to unscrew water connections from valve.

took the back off refridgerator, disconnected water valve assembly, then disconnected water lines and electrcal connectors. also i received the part in less than 24 hours

This is an easy repair. Unplug appliance. Remove the old water valve by unscrewing it from the frame of the refrigerator. Disconnect the cables and all the water hoses. The hose fittings are a different type: clip off the old connectors from the hose ends and push the hoses straight into the new connectors till they fit solidly. Reconnect the cables and screw the valve back onto the frame of the refrigerator.
Unfortunately, my leak was from a hose, not the valve, so this didn't actually fix it.

took existing water valve loose, removed plastic water lines and reinstalled on new valve and installed new valve into refrigerator

I had a repair man do the work.
That's always best.There was one day delivery on the part and the price was great. Thanks

Twist to remove the old one an twist to install the new 9ne

turned off water supply, removed cardboard back, removed supply line, unhooked all color coded connections,took out bad water valve and replaced with new one note: the new valve came with pex connections so i carefully cut off flared tubing ends with sharp razor knife making sure when i pushed tubing into new valve that i did so with some force until i HEARD and felt them snap in place very simple plus i received the new valve in 2 days very happy with PartsSelect.com you CAN do it

Turned off water supply disconnected hose from valve removed cardboard backing removed the screws holding valve ass'y disconnected the three wire connections disconnected five hoses then cut and installed in new valve per instructions provided reconnected three wires reinstalled valve ass'y turned water supply back on and checked for leaks by engageing filtered drinking water in the refrigerator door replaced backing to complete job.

remove back cardboard panel, cut off water supply, remove screws holding valve to back of refrigerator, unscrew water lines & reattach to same fittings on new valve, screw new valve in place, replace cardboard cover.

First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

This was probably the easiest repair I have done on this refrigerator. I pulled the unit away from the wall, turned off the water, and disconnected the hose. I have a wooden floor in my kitchen so I was careful to put a towel under the hose and valve. Very little water drained out but I kept the towel there for insurance. After removing the access panel, I removed the two screws holding the valve in place, slid it back to where I could unplug the wiring connected to it. The connectors are color coded so there is no worry about putting them back incorrectly. The new valve uses push-in type water connections, so you have to cut the old style connections off of the plastic water lines. Kitchen shears did this easily. Then is was just a matter of pushing each line into the proper connector on the valve, reattach the electrical connectors, and slide the valve back in place. Reinstall the screws, reinstall the access panel, hook up the water hose, slide the unit back into it's niche, and run about a gallon of water through the dispenser and you are done.

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings