Models > DDW361RAB-PDDW361RAB0 > Instructions

DDW361RAB-PDDW361RAB0 Amana Dishwasher - Instructions

All Instructions for the DDW361RAB-PDDW361RAB0
76 - 90 of 255
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken wheels on dishwasher racks
The plastic wheels on the upper and lower racks keep breaking. The latest casualty was also chewed up by the dog(s). They just pop right on the posts, a simple 2-second fix. I ordered the parts on a Tuesday morning, standard shipping, and they arrived FedEx less than 24 hours later. They came from Peoria, and I live about 1 hour away in Bloomington. Very pleased with the service. Will order from PartsSelect again if I need parts for any other appliance that I can fix myself.
Parts Used:
Lower Wheel Assembly
  • Paula from Bloomington, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rollers broke
They just snapped in to place. Once I realized where they went. They are not the exact rollers needed but will do until I get the right ones. The rack will not come out as far as it should because of the difference. Other than that....easy.
Parts Used:
White Dishrack Roller
  • Leanne from Fremont, NE
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking at door
I tried tightening the latch (this had worked once before), but it was already tightened as far as it would go, and door still leaked. So I suspected the gasket, because the old one looked like it had lost its elasticity and was caked with crud. I tried cleaning it in place, but it still leaked. So I ordered a new gasket. However, it was back-ordered, so I tried removing the old gasket and cleaning it. It came out very easliy ( I had expected it to fall apart). Then I cleaned it good under running water, kneading the crud out of it. I also cleaned ou the groove, then I replaced it and that fixed the leak. So I didn't need the new gasket.
Parts Used:
Door Gasket
  • Walter from Mahwah, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Door Spring Linkage
Turned off the water. Disconnected the water supply line. Extracted 2 screws holding the dishwasher. Pulled out the dishwasher. Changed out the nylon spring link. Pushed the dishwasher back into place. Reattached the water line. Turned the water back on.

Spring linkage and postage about $15.00.
Savings on service call and parts about $175.00. What a deal. Thank you PartSelect.
Parts Used:
Door Spring Linkage
  • Lester L from Edmond, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring assist on door failed,
Removed front access panel
Disconnected water supply
Pulled dishwasher out approximately 1 foot to gain access to spring linkage
Connected new spring linkage to spring, connected other end of spring linkage to door
Tested operation of door
Slid dishwasher back into place, reconnected water supply and front access panel
Parts Used:
Door Spring Linkage
  • Robert from Flushing, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench set
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Detergent cup wouldn't open/Leak along bottom of door
Replace wax timer for detergent cup. Replaced foam insulation at bottom of the door.
Parts Used:
Adjustable Peg Clip Inner Door Foam Insulation Strip Wax Motor for Detergent Cup Actuation
  • Shan from Medford, OR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door spring linkage, a plastic part, broke so the door spring didn't hold the door upright.
Took off the lower front plastic piece and unscrewed the side panel to snap the new part in place then attached the spring to it.
Parts Used:
Door Spring Linkage
  • James from BETTERTON, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher was overfilling
Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.
Parts Used:
Float Switch
  • James from AMISSVILLE, VA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door spring linkage
On my dishwasher, one linkage broke, making the door feel heavy to raise and lower. Because there are two door springs, one on either side, I decided to replace both plastic linkages even though only one broke, because it would only be a matter of time before the other plastic link failed and I would have to do the repair all over again. Remove the 2-piece panel at the bottom front of the dishwasher. It's held on by four hex-head screws which also have slots for a Philips screwdriver. The springs can now be seen on both sides of the door, at the bottom. Remove two screws that anchor the dishwasher to the underside of the counter. Gently ease the dishwasher a short distance out from its under-counter recess, just far enough to gain access to the springs. Make sure not to put any excessive strain on the water inlet tubing, drain hose or electric power cable by pulling the dishwasher out too far. Close and latch the dishwasher door so that the springs are in minimum tension. Note the slot that the linkages hook into on the door levers. Hook the small end of the spring into the hole in the metal bracket. Slide the linkage onto the other end of the spring. Stretch the spring to slide the free end of the linkage onto the door lever and into the appropriate slot. Push the dishwasher back into its recess and replace all screws and panels.
Parts Used:
Door Spring Linkage
  • Brian from SAN DIEGO, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The plastic linkage that connect the spring to the door broke
The time to hook up the spring was a minute or two. I simply attached the linkage to the door and then attached the spring to the linkage.The extra time in the repair was re-attaching the cover.
Parts Used:
Door Spring Linkage
  • William from MORGANVILLE, NJ
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking in front right bottom corner of dishwasher
I removed the gasket from around the dishwasher. Cleans the grove of any dirt, mold or other debris. I started the gasket replacement at the top center of dishwasher by folding the gasket in half to find the center and inserting that center point into the grove just below the latch.i then inserted the rest of gasket with my thumb into the remaking grove first to the right corner then to the left. No told were needed leak was gone
Parts Used:
Door Gasket
  • melvin from CHICAGO, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door dropped one day after a loud "pop"
I took off bottom front and kick plate. Retrieved the spring which had flown to the rear of the unit. Cannot pull unit out because the trim piece on the counter top was put in after the unit was screwed to the underside of the counter. So... I noticed that you could move the plate the bottom of the spring hooked into by unscrewing a long quarter inch hex head bolt and bring the plate forward where I could hook the bottom of the spring into the plate. I had first hung the door spring linkage on the door (looked at the opposite side to see how it was arranged) then onto the top of the spring. The difficult part was keeping the bottom of the spring in its hole in the plate while moving the plate back in place. After I got it past the flange where the bolt screwed in, I screwed the bolt in and pulled the plate back to match the opposite side distance which put tension on the spring. The door now works. I am fortunate to have my husband's tools available.
Parts Used:
Door Spring Linkage
  • Mary E from SILT, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Detergent Dispenser Latch broken caused Detergent Dispenser not openning
Use Screw driver to open the dishwasher door cover, you will see the Detergent Dispenser. I just took pictures before I remove any parts including the wires in case I forget where to put them back.
Parts Used:
Detergent Dispenser Latch - White
  • Qingrong from NAPERVILLE, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
It was leaking out of the front door of the dishwasher
Pride old gasket out with screw driver easily removed it cleaned where the gasket was with mild detergent and easily installed new gasket
Parts Used:
Door Gasket
  • Patrick from MURRAY, UT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leak
I just followed other directions that were on this sight piece of cake. Preperation took longer than the repair.
Parts Used:
Top Shower Pump Hose
  • Larry from PARMA, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the DDW361RAB-PDDW361RAB0
76 - 90 of 255