DCVH515GF2WW General Electric Dryer - Instructions

Took apart by removing the top and front panel. Found drum rubbing due to worn glides and felt.

First I laid the cabinet on its front so that it was easier to remove the back sheetmetal screws on the right hand side. I then opened up the right side of the cabinet and held it open with a 2X4. I was able to reach inside the cabinet and unplug the wiring. It was more difficult reaching the ground wire and removing the screw that it was attached to however i found that using a socket with an extension was the most effective. The cordset popped right out with the assistance of a flat head screwdriver. The cordset and ground wire were set in place and attached without trouble.
It was difficult trying to figure out how to open up the cabinet without instruction!!!

I first unplugged the unit, opened the top, disconnected and took off the control panel, took off the front panel to determine the source of the squeaking noise coming from the Dryer. I saw that 3 of the 4 Front Drum Glides were gone and the drum had worn away significant amounts of plastic from the Top Bearing Assembly. I purchased the Top Bearing Assembly and a set of 4 Front Drum Glides. Disassembled the damaged parts and reassembled with the new replacement parts. The reassembly took less than 20 minutes. I plugged in the Dryer and viola! It works as good as new.

I unscrewed the inside of the dishwasher door and clearly saw the old interlock switch. This dishwasher has two, but it was obvious that one switch worked and one didn't (one switched was permanently pressed in). I removed the old interlock switch. It was tricky to pull out and I felt like I was going to break it but after watching youtube videos, I was pretty sure you just have to pull hard. I easily put the new switch in, reattached the dishwasher door, and it works perfectly!

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

I've experienced same symptoms on previous dryers over the last 30+ years, so I immediately ordered a rear drum bearing replacement kit from PartSelect. Perfect replacement parts for replacement of OEM parts.

1) After unplugging dryer, moved it to garage because of expected dust and lint deposits.
2) Removing two screws under from top lip allows top to lift and rotate off of dryer.
3) Removing two screws inside on both sides allows the front panel to be removed. Just remember to lift drum when you pull pannel off.
4) Best to take front panel off completely, so remove single screw on green ground wire at lower left and disconnect the white two wire connector (pull apart). Three wires need to come off of door switch (yellow/brown and white leading from the dryer inerds and one white to the drum light). Best to tag or remember where they connect. Otherwise, white from inerds goes to switch common, y/b goes to normally open and bulb white goes to normally closed terminals.
5) Get someone with really skinny arms to reach in to slide drum belt off of idler pulley. Otherwise, long sleeves are a necessity to keep from getting sliced to pieces on sheet metal edges.
6) Lift drum out and away from dryer frame. It's a pretty tight fit so get a helper to spread the side panels apart a bit.
7) Replace both bearing pin in drum and bearing socket in heater pan, following instructions that come with the parts or the video that is on the PartSelect website.

Didn't expect the drum slides and top drum slide support to be worn out, so I had to order them ASAP from PartSelect. The slides were totally gone and the support assemble was effectively toast. You might seriously consider replacing the slides and the lower felt when you try to fix the squeeks, since they are a major source of the noise and take an additional 2-3 minutes to replace.
8) Reassembly of the dryer is just doing the above steps in reverse. Best to clean out as much lint/dust as possible, since a clean dryer is an efficient dryer and we all want to make our "green" friends happy nowadays.

Pulled the unit all apart to replace the rear drum bearing. Also replaced the front bearing. Works like brand new. Easier then I thought

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Took out interlock switch (two leads) and replaced with new one. As simple as that.

Removed panel to access the interlock switches. There were two. The button on one switch was fine and the button on the other would not depress. Ran a continuity test and it failed. The switch also had a burnt smell

My washer and dryer set are stackable. First I had to take the dryer down from atop the washer. I thought the problem was the rear bearing.
When I received the new rear bearing I watched the video and proceeded to take the unit apart and then I realized the top bearing, slides and the felt seal were completely destroyed so I ordered the rest of the parts I needed It took about 5 days to get the parts and less than 30 min to install. The videos were a big help. I had no Idea what I was doing and was surprised how easy it was. It was a Big savings over buying a new dryer.

I watched a video and followed the video instructions. Spot on and fixed the problem. Very easy repair.

Replaced front plastic bearing and bearing slides for less than $90.00. The repairman from Sears said it would cost at least $300.00 in parts plus labor to repair it, he suggested buying a new dryer (what an idiot). This was a very easy repair, I found instructions on YouTube. 15 minutes and a Phillips’s screwdriver is all that it took. The dryer runs perfectly with no shudder or squeal.

Easy repair, but did take a little longer than anticipated due to the extra cleaning that I did while the dryer was disassembled (highly recommend). First, unplug the power cord. Then, open the door, and locate the two screws in the upper corners, and remove. This will allow you to remove the top cover. Be careful and work the top panel up and down to loosen the control panel tabs, and set aside top panel. Next, remove the two screws located near the top on the inside of the front panel. Removing these two screws will allow you to lean the front panel forward, lift up, releasing the tabs holding the bottom of the panel. Be careful when you pull the front panel from the dryer as you will need to lift the drum off of the front bearing which is attached to the front panel as it is removed. You will also need to use your needle nose pliers to remove the wires prior to setting the panel aside. The wires are straight forward and power the light at the top, and the safety door switch. I always take a picture with my phone's camera just to validate when I re-connect them. Reaching underneath the drum you will be able to feel the belt and belt tensioner pulley. With both hands under the drum, use one hand to push the pulley to the right, releasing tension on the belt. Move the belt out of the groove, and let it hang freely. Now from the top of the drum, bump the drum to loosen, and remove from the cabinet. It is a tight fit, so you will need to spread the sides slightly in order to remove the drum. Next, remove the 3 screws holding the heat diffuser in the rear of the drum in order to remove the rear drum bearing. (Tip: It would be nice to have a helper hold the new drum bearing in place when starting the screws, and it also helped to tighten each a little at a time to keep the new bearing flat as it was drawn up next to the drum.) Tighten the screws holding the new bearing in place. Next, remove the 4 small screws holding the heating element housing to the rear of the dryer. (Tip: Rather than disconnecting the wires, I used a bent coat hanger to hold the housing while I removed the bearing retainer and clip from the rear of the housing.) Remove the 4 screws holding the bearing retainer and clip, and replace with you new part, paying close attention to the clip's position, and tighten. Replace the housing to the rear of the dryer. (Tip: Now is a good time to familiarize yourself with the belt and tensioner pulley for reassembly. Also, it may be a good idea to look at your belt, and replace as needed.) Next, reinstall the drum and insert the new bearing shaft into the new bearing housing. Using both hands again, reach underneath the drum, locate the tensioner pulley, and belt. Push the tensioner pulley over to the right, and move belt over the pulley on the motor, and behind the tensioner pulley. The belt should be tight. If not, inspect to ensure that the belt is over the motor pulley, and the tensioner pulley. Next step is to reinstall the front panel. I also spent the extra money and replaced the front drum bearing, and slides. Please note that the green slides are on top, and the white slides are on the bottom. Lift the panel over the tabs, lean forward while lifting the tub, resting the tub on the front bearing. Reinstall two screws in the upper corners, and tighten the front panel back in place. Now is a good time to turn the drum to ensure that the belt is in place, and that the drum turns correctly. (Tip: If your dryer is equipped with a light, you may also want to replace the bulb in the front panel (if needed) prior to attaching the front panel.) Reinstall the top panel by aligning the tabs in the control panel with the top panel, being careful not to bend the tabs. Next, open the front door and use the 2 long screws to reattach the top panel to the front panel. Plug in power cord.

One thing to note that I didn't immediately notice. Upon removing the front panel, there is a chance the drum will stick and when you separate the front panel from the drum, this will pull it from the rear bearing. We did not initially realize this was the case until the dryer was back together and would not run. If there is any resistance, we found the easiest way to solve the issue is to lay the dryer supported on its back, then everything slides in and out. the second time through from start to finish took less than 10 minutes. I loved the videos and the parts. I tried cheating and getting the parts on amazon, and wound up buying from this site anyway and paying even more to have it rush shipped.. All in all super glad I did it and didn't buy a new dryer, I think we can tackle replacing anything on it at this point.