CRSE264JQ2 Frigidaire Refrigerator - Instructions

Consult the exploded view of the Ice Container on this site. A likely cause the end plate (17) is worn. This plate connects the rotating corkscrew to the final plastic worm that pushes the ice into the crusher and thence to your waiting glass. The worm alone will not do the trick. To replace this plate, you need to take out all of the screws you can see, including the one that holds the spring for the crusher select bar.. First, the front cover, then the plate, and finally, locking ring from the worm and the black housing for the crusher. Now you can remove the whole worm assembly. Using a cloth or rubber insulator to protect it, unscrew the end screw and slide off the crusher teeth. Store on the table as a unit to facilitate re-assembly. Slide off the old bar and worm, put them back, and re-assemble. Takes a little dexterity to get the crusher select bar back, but not hard. Easy job.

Took the ice storage bin out. Took the unit apart,and disamble the augar unit. Ordered parts from manufacture, which arrived in two days. As soon as I got the parts, I reassambled it. Work perfect. Good job!

Removed screws holding unit and removed unit. Removed switch from connectors in unit. Replaced unit without switch. On day switch arrived (delivery was prompt) my wife replaced switch by attaching the two connectors and slipping into unit without having to remove entire unit. How easy was that!!!

Used pliers to remove filter.

The parts arrived much quicker than expected. The parts were exact matches and they snapped into place within minutes.

Remove the bottom freezer drawer. Remove back metal evaporator panel. Wire in new defrost terminationT-stat. Reassemble evap panel. Good to go.

I ordered the parts by studying the diagram and they were perfect. Thanks for making it so easy.

I removed the ice container found the part # on the bottom ordered a new one and installed it. It just slipped right in to place.

2 steps; 1. I removed the broken door bin 2. I slid the new door bin in place, Am I a genius or what!

Twisted replacement bulb into place easily. Let there be light!

Support studs have an expansion fitting - center post has to be pushed through to allow expansion joint to collapse for removal. After installation, this post can be pushed in or pulled out to secure the stud and be the proper length to hold the bins.

None of this was obvious - an online tip from another member was invaluable.

This was a replacement part, a simple snap in. What really impressed me was the PartSelect web site and the ease of locating the part and making sure it was the right one. Finally, the price beat out all the others. Since this tray looked like others on the same unit, I needed the details, the different view angles and dimensions to make sure it was correct. No other web site was even close in ease of use or in providing such details. I know I won't waste my time at PartSelect and I've always gotten the right part at the best price.

Looked at video on how to remove and reinstall support and followed the instruct ions

REMOVED THE DRAWER, LIFTED OFF THE GLASS, REMOVED THE BROKEN SLIDE, AND PLACED THE NEW SLIDE IN THE PROPER SPACE. REPLCED THE GLASS SHELF TOP AND THE DRAWER. PEICE OF CAKE

I unplugged the refrigerator and removed the back panel in the freezer. Here the coils were covered in a block of heavy frost. The coils needed to defrost, I allowed this to happen of the course of a few hours. Once this was done I used the wire cutters, cutting the two wires to the thermostat. Doing this I checked the continuity & got no reading. Having ordered the part at a more than reasonable price including 2 day delivery, I was ready to complete the repair. Stripping the thermostat wires connected the the freezer unit, I attached the two wires color to color to the new thermostat. Here I needed to insert both ends into the connector (butt end), crimping both sides. Making sure each end I'd secure. Do this for both sets of wires. Placing the new thermostat back on the the cooper coil (on the same one it was removed from), put the freezer back in place. Here I only screwed in two, in case I need to go back in. I plugged the refrigerator back in turn the settings back to default or factory. Allowed the refrigerator to come back up to temperature for 24-48 hours. I did these and I'm glad to say my 12 year refrigerator is working just like before.