ATW4475XQ0 Admiral Washer - Instructions

Woulkd have taken alot less time had I not taken off the control board, back...etc. Laying the unit on its back is perfect. Took it out into the garage when I could have done it in the laundry rooom with very little water loss.
1. Removed all hoses connected to top of motor. This was not very easy since the spring clamps had been in the same place for 20+ years. Also removed all wire harness connected to and from the motor.
2. Removed metal clamps from top of motor unit, and removed the plastic "valve".
3. Removed screws holding in clamps on each side of the motor used to hold motor on motor plate. Removed motor. Trick is to make sure that the back clamp stays in place...makes it a little easier when you go to re install.
4. Cleaned out around agitator shaft, and fitted one side of the coupling and the neoprene type joiner on to the agitator shaft.
5. Fitted other side of coupling on to motor...This is where it got a little tough......and then placed motor unit on the motor plate, making sure to line up teeth to neoprene joiner.
6. Replaced clamps on each side of the motor and screwed in nuts holding them in place.
7. Replaced plastic "valve" and the clamps that hold it in placed...back one is a little tough.
8. Reattached hoses to "valve" and hooked all wire harness back into place.
9.Tested perfect...little burning smell on first spin....but works great now!!

Used screw driver to pop top off to access the bolt on spinning unit.Used socket wrench and took bolt off of bottom of spinniner. Replace agitater with new parts and reassembled. Now it works like new.

I removed the cabinet and agitator, layed the machine on it's back, removed the pump, motor and gearcase. I found a way to prop the gearcase up so it rested level, removed the cover, drained the old oil. I removed all internal parts, disassembled them and cleaned them. I reassembled the gearcase using the new uetral drain assembly, and replaced the oil. I made sure the brake assembly was pushed into position and then put the gearcase, motor and pump back in. I sttod the machine up, put the cabinet back on and tested the machine. It still did not spin, so it wasn't the coupler, clutch or nuetral drain assembly.

undo one bolt and change agitator kit

I watch the video... that simple!

I did a Google search for the model number and found this site, PartSelect.com. Based on the diagrams on the site and what I could see underneath the washer, it was clear that the motor coupling was now gone and the shattered pieces of it were all over the floor. So I ordered a new coupling and waited for it to arrive, it was shipped in just a few days. Once I had the new coupling all I had to do was remove a couple of brackets holding the pump onto the motor, and the motor onto the gearbox; unplug the electrical terminals and lift the motor out. There are two halves to the coupling, one sits on the shaft of the gearbox and the other on the shaft of the motor. Both of these are seated into a rubber boot that is also a part of the coupling. Once the motor is sitting on the gearbox with all the coupling parts seated in place, just plug everything back in and replace the brackets. You will need a 1/4 socket to remove/replace the motor brackets. Also, it should be noted that you will want to unhook everything that is hooked to the wall (hoses, power cord) but it assumed you've already done this if you have access the the underneath of the washer.

Took an educated guess it was the lid switch and after playing with the switch got it to work. Ordered new switch. The hard part was to find the model number and thanks to customer service sticking with we. we found the info and was able to come up with a part number. Re placing the switch is very easy but I had to remove the cast after trying to open the machine the wrong way. So a little body work. I also found the frame was cracked and with a fender washer on the other side of the front feet was able to fix that. Washer run great a lot is a lot quieter.THANKS!!

Removed softener cup agitator cap and one bolt, lifted agitator out and replaced with new one... tightened bolt replaced cap and softener cup and away we go, done...

Popped off agitator cover discovered worn and broken 'dogs'. Decided to replace complete agitator assembly due to age of machine (25 + years). 7/16 socket, removed nut and agitator assembly, installed new assembly with included nut.

I needed the washer ASAP. I paid extra for the expedited shipping. The parts arrived as promised. I watched the on-line video. I read and followed the included instructions. Removed cap and nut. Pulled out part with "dogs", swapped new dogs and assembly. Re-installed components, I was wary from information gleaned from the video, which warned of proper orientation of "dogs", as they can be inserted backwards. Tightened bolt and re-installed cap. Presto! Repaired washing machine worked as good as new. My coffee didn't even get cold.

On my model You have to first lift the control panel in order to remove timer knob.I removed control panel by prying on the ends of panel one at a time with putty knife and rag to keep from scratching washer. I then use needle nose pliers to pull plastic under side of knob while pulling on knob which is the trickiest part of the job as knob will not come of til it is pulled from underside with needle nose pliers to release it then its easy from that point to disconnect wires and slide timer to the left to unlock it and in stall new timer.You have to take your time doing the repair and it will work out better for you.After replacing timer machine works on all cycles and completes entire cycle. Thank You PartSelect!

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

will not go over step by step here as there are already a multitude of stories on site with exact situation as mine who have already done so.. What I will say is that PartSelect is easily the absolutely best site on the net for a complete problem diagnosis to finished repair experience. Just input your model # and describe the problem and you get instant diagnosis probabilities along with access to a long list of customer Q & A and reviews, along with step by step videos on diagnosing, dis- assembling, and re-assembling along with links to all parts needed and also some secondary tips along the way. The prices are fabulous (example: I got a clutch assembly kit with several parts and 2 additional parts as a just in case for $55 shpg incl, while my local appliance parts place wanted $59 plus tax for just the main part in my assembly kit with a no return policy and no part guarantee, plus it was only 1 day more to have PartSelect pkg arrive than I would have gotten part from local store). This site is FABULOUS !!!

replace clutcher

Disassembled lower part found nothing wrong.
Started disassembly from the top. Immediately ran into trouble not knowing exactly how the tub was anchored to the drive. Once I got down to the tube and drive block there was nothing I could do to go further. I guessed it was a press fit onto the drive, but there were many instructions and I couldn't be sure. Parts Select expanded drawing was the most useful tool; it was correct omitting a few details. Anyhow, cleaning out my garage I found one of my old gear pullers that I could ring to complete the disassembly. All the sudden I was in business, pulling the washer drum off the drive block and shaft, getting down to the leaky lower seal. A that point it was just a matter of cleaning everything up and buying all the rusted out parts to reassemble. I spent $150-200 on parts, but its completely rebuilt now and runs like a charm. Probably have around 20-50 hours all told, into the repair. Most of this was reading instructions, watching videos, and trying to figure out the rest (3). Doing the actual work spread over time until my wife and sons threatened to throw the thing out. Never. Once I decide I'm gonna do something, I do it. LOL!