ASI2175GRB03 Maytag Refrigerator - Instructions

looked at the schematics from online

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

The video for the repair was very helpful and made the repair go very well. It works just like new!!

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

new auger and drive wheel

auger blade was replace

I removed the external shaft that controls the ice grinder. Its spring loaded so you have to remember how to get it back together. I removed the screws that hold the cover in place. I removed the nylon nut that holds the drum and grinder on the center shaft. I replaced the drum and reversed the procedure.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

We didn't know how to remove the damaged handle and attach the new one to the freezer door. We had planned calling Whirlpool's Customer Service dept. for instructions. However, we didn't need to. By looking at the handle ends my husband new what to do. He applied pressure to the old handle in a certain angle pulling it from the freezer door, and it came out easily. Then to install the new handle he applied pressure pushing against the door until it clicked right in place. The new handle attached to the door perfectly and it's very firm in place. The refrigerator looks like brand new.

Awesome price, awesome service, and great experience. I must say I was apprehensive about repairing my refrigerator’s ice maker, but the pieces of plastic and the $150 estimate to repair the bad part helped to motivate me into action. I quickly found the part I needed on your website at a reasonable price and placed the order. I fully expected to wait 6 – 8 weeks for the part to arrive but to my great surprise it arrived in just two days! I maintained and repaired complex ordinance and missiles in the Air Force for 21 years but a couple of steps in the repair of this icemaker stymied me, until that is, I watched your repair video! What a wonderful resource that was, step-by-step instructions on the entire repair…. Armed with this resource a guy just can’t go wrong and in short order the repair was complete and I am back to crushing ice again. What a wonderful service you provide and I couldn’t be a happier customer. You folks at Partselect.com have your stuff together, keep up the good work.
Mr. William L. Austin, M.Ed.

I followed the video. And it was a big help

Great! I actually replaced the Auger Drum while watching the step by step video on my PC. Do not think I could have completed this replacement so quickly without the video. I would recommend PartSelect to anyone. Thanks

Was easy, removed several screws and a clip on the auger shaft. removed broken part and replace with new then reassembled