ADE20L1W Admiral Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
broken heater element
Replaced thermocouple and heating element, clean build up dust lint inside as well. Actual repair takes only removal of 2 screws. Cleaning inside takes longer.
Parts Used:
-
Richard from Great Falls, MT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mouse ate hole in lint filter
Glad I ordered 2 lint filters. Mouse ate a hole in the new one also. EXCELLENT service, by the way. Received filters less than 24 hrs. after ordering.
Parts Used:
-
Diane from Andrews, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas dryer not drying clothes in one cycle
Unplugged the dryer. Released the two forward sping clips holding the top in place and hinged it open. Removed the two 1/4" screws(one on each upper edge of front panel). Disconnected the door switch. Pulled out and up to remove the front panel. Located the cycling thermostat on the blower housing. Disconnected the thermostat wires, removed the (2) 1/4" screws. Installed the new thermostat and assembled in reverse order.
Parts Used:
-
John from Saint Petersburg, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
3 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blower wheel broke off of shaft.
Purchased a new blower wheel from you and installed.
The part was exactly what I needed and was delivered ahead of schedule. Ordering over the internet was easy and straight forward.
The part was exactly what I needed and was delivered ahead of schedule. Ordering over the internet was easy and straight forward.
Parts Used:
-
Richard from Opelousas, LA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer Element Not Heating
Daughter and I lifted top of dryer, carefully removed old element and thermostat, watching as we went how the old ones came out, and replaced with new one! Dryer working just fine!
Parts Used:
-
Florence from Center Point, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced lint filter on dryer
-
Kenneth D. from Norcross, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat
Tilt dryer top. Inspect damaged part(s). In my case it was the high-limit thermostat; but since the dryer is old, I ordered the heating element kit. The thermostat is included. Disconnect wires from thermostat and remove. Disconnect wires from element and remove. Carefully install new element and reconnect wires. Same for thermostat. Dryer works fine. Also, delivery time was one day. Thank you Partselect.
Parts Used:
-
Fred from Snailville, GA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer doesn't heat
I used a butter knife to push the spring clips that hold the top down, this was the hardest part of the repair. Once the top was open it took about 20 minutes to pull out the old part and replace with the new, including running the dryer on high for a few minutes to get rid of the new element smell. Always unplug before attempting any electrical work.
Parts Used:
-
David from Roswell, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original lint filter was separating at the edges
Removed the old lint filter and slid in the new one. It took me longer to get the box open to get the new lint filter out than it did to actually replace the part.
Parts Used:
-
Barbara from Altoona, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lint filter broke
-
Kellie from Lake Wales, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
no heat
It was very simple thanks to your notes on line
I would use your site for ordering any other needs I have.
Thank You
Robert
I would use your site for ordering any other needs I have.
Thank You
Robert
Parts Used:
-
robert from Jarrettsville, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the frame of the lint filter was cracked
well.....first I opened the dryer door and pulled out the old cracked lint filter...then I took the new lint filter out of the plastic bag and put it in the dryer......and then I closed the dryer door.....then I had a beer.
Parts Used:
-
stephen from Harrisburg, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Heat
UNPLUG DRYER!!
1)Opened top with putty knife pushing on the two spring clips.
2)Removed Hi Limit switch w/bracket (1 screw)
3)Removed Old Element (1 Screw)
4)Installed New Element
5)Replaced Hilemit Switch on bracket (2 Screws)
6)Reinstalled Hi Limit switch/bracket
7)Reinstalled wires/Closed Lid/Plugged In/Started Up....No Problem
1)Opened top with putty knife pushing on the two spring clips.
2)Removed Hi Limit switch w/bracket (1 screw)
3)Removed Old Element (1 Screw)
4)Installed New Element
5)Replaced Hilemit Switch on bracket (2 Screws)
6)Reinstalled Hi Limit switch/bracket
7)Reinstalled wires/Closed Lid/Plugged In/Started Up....No Problem
Parts Used:
-
Ron from Kosciusko, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door would not stay closed because metal latch piece was gone.
I ordered the part. ( I should have ordered just in case it happens again.) When it got here it took less than a minute to snap it in.
Parts Used:
-
Ian from Greeley, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Catch broken
The old door catch broke and fell into the unit. Ordered the new part which arrived fast and snapped it into place. Perfect fit and the door now closes/latches correctly - like new again. Would recommend your web site to all do-it-yourselfers. Loved browsing your site, especially seeing all of the schematics and parts list for my unit.
Parts Used:
-
Wayne from Columbiana, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!