ADB3500AWW41 Amana Dishwasher - Instructions

In order to clean the screen I had to remove the impeller. Removal required using a wheel puller. I backed off on the impeller screw but left it attached so that the wheel puller could pry against it. I then tightened the puller enough to free the impeller. I was then able to unscrew and remove the screen for cleaning.

Removed the old one....slid in the new one.

Turned off water at the shutoff valve. I did not turn off the power, but it is recommended you do so. I pulled the dishwasher out from under the cabinet and used a car jack to lift the front off of the ground. Disconnected the water supply and the rubber hose that fills the dishwasher tub. There are two 7mm screws that hold the water pump to the frame. If you do not have a 7mm socket, the easiest thing to use is an interchangeable screwdriver. When the screw bit is pulled out, the empty screwdriver is a 7mm. Used adjustable wrench to remove the brass water port for the supply line. Teflon tape to all connections and hooked everything back up. My supply line was old and was leaking, so I had to run out and get a new one, so that added about 30 minutes to what would have been maybe a 20 minute repair.

Lifted the old spray arm off, put the new arm on the spindle, screwed on the cap with my fingers. Good to go.

I just took the nut off and replace the washer arm it didn't take any time at all.

1. Remove both upper and lower dish trays
2. Remove the “Spinner /Sprayer” (small nut on the top)
3. Unclip the “Tower” from the top and rear clip
4. Remove the “Tower” from the unit
5. Remove the “Filter Guard” on the bottom by removing 3 torx screws
6. Remove the “Discharge Housing” & “Impeller” (1 – 15 torx screw)
7. Remove and replace the “Accumulator Filter” (8 – 20 torx screws)
8. Assemble in reverse order

I followed the instructions here on PartSelect to dismantle and put the new impeller in to place. Could tell the difference just in sound alone once it was running.

The repair went easy. Just unscrewed the inside door panel and latch assembly. Then put the new one in. The only bad thing was I purchased the latch assembly with out the handle and found out mine was cracked. I looked back on-line and couldn't find just the handle. Everybody sold it with the latch assembly. I thought I would save the 2 bucks buying the assembly without the handle. But in the end the door seals tight and no water leaks.

Replacement parts were an exact match so overall it was pretty simple. At the front end of the rack guide rail there is a removable stop. After removing the stop the old guide wheels can be removed from their "axles" (actually a part of the wire rack is bent at 90 deg to act as an axle), and simply moved forward and out of the guide rail. Took a few minutes to clean the guide rail, then installed the new guide wheels and pressed the removable stop back into place. Works like new.

n/a

Snapped new roller on to dish basket frome

It was very simple and easy. I opened the panel inside the door; total of 8-10 screews. The latch has two electrical connections and switches. The replacement part I got came with an extra set of switches. Replacing the switches needed an electrical tool which I don't have so I decided to keep the old ones. It is quite easy to take out the switches and replace the latch. I should have taken out the power; but I did not. I was just careful handling the wires et al; no big deal either. My dishwasher is working fine now. I was able to fix it within $40 and 1 hour of effort. Any technician would have cost me atleast couple of hundred bucks + parts etc.

took the broken ones off and snapped the new ones on.
easy as pie. took less than 5 mins.

Removed dish racks, snapped out docking station and snapped in new station. Works great! Saved big bucks. Thanks.

We removed upper basket by snaping open and removing rollerslide caps. The docking station simply snapped into place. It only snapped in one way so we were certain it is installed correctly.
That part was missing from the factory and I feel a little angry that we had to buy it and install it ourselves. We would never have known why our dishwasher wasn't working like it should if we hadn't seen the inside of another one that belonged to a friend.