Models > ADB1100AWB4 > Instructions

ADB1100AWB4 Amana Dishwasher - Instructions

All Instructions for the ADB1100AWB4
61 - 75 of 147
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Arm did not turn!
Removed old arm and put knew one on!
Parts Used:
Upper Spray Arm
  • Sandra from HIGHLAND, NY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not drain
After bailing out the unit, filled filter hole with a moderate amount of Dawn dish washing detergent. Ran dishwasher twice to remove all Dawn from the unit. Had to bailout the water (and suds) from the washer both times. After the dishwasher finally drained I inserted the new filter..
Parts Used:
Dishwasher Filter
  • Edward F from CINCINNATI, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Someone had used the wrong type of power cord
Recently bought a whirlpool dishwasher, the dishwasher was converted to a portable dishwasher and they did not use the cord application power cord so they machine was blowing our breaker, instructions were very simple and installation was easy!
Parts Used:
Power Cord Kit
  • Jonathan from DOWNS, KS
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not start & green "Clean" light was flashing
After reading customer notes regarding the same problem I was having I ordered A new Heater Element & a High Limit Thermostat. I also ordered a Heating Element Nut and Rubber Washer in case I needed them. It took me quite some time to remove the dishwasher from under my counter. Once the unit was out and prepared to service it actually took only a few minutes to install the new Heater Element. I did't need the washer or extra Nut. I also decided to try the unit without replacing the thermostat. I cleared the diagnostics by pressing the "HEATED DRY, "NORMAL", "HEATED DRY", "NORMAL" buttons. After the controller reset the dishwasher was ready to run.
Parts Used:
Dishwasher Heating Element
  • DAVID from MILWAUKEE, WI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
element not working
laid dishwasher on its side and unscrewed element. returned unit upright & replaced element. reversed process and reinstalled unit under cabinet
Parts Used:
Dishwasher Heating Element
  • Michael from Springhill, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water not heating,dishes not drying
My husband did this. He turned the dishwasher upside-down, disconnected the wires,and unbolted the heater.He put in the new heater (bolted,wired) and tested the current. Voila!
Parts Used:
Dishwasher Heating Element
  • Marie from Hollywood, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishracks wre worn out
quick and easy replacement, without tools...

i ordered the wrong part and received the new part and credit for the old part, quickly...Plus, I was kept informed with e-mails....

excellent service...
Parts Used:
Upper Dishrack
  • BRUCE from TOPEKA, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
6 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Develeoped a leak on the bottom.
Pulled dishwasher out of compartment, removed all parts underneath. removed inner parts, removed pump assembly. Installed new pump assembly and grommet. Reassembled in reverse order, test ran and unit was operating normal and no leaks.
Parts Used:
Grommet
  • Eladio from LOGAN, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench (Adjustable)
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front Track stop missing
Snap new track stop into place. Took a few minutes to figure out top/bottom and inside/outside, but no issues
Parts Used:
Rack Track Stop
  • Tim from GLADSTONE, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old cap came loose, fell onto heating element. End of story.
Bought the new cap, took it out of package, installed.
Parts Used:
Dispenser Cap
  • Raymond J from MOKELUMNE HL, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element was no longer working. Dishes were not drying.
Watched a video and seen how easy it was to repair. Just disconnect the power, water and return drain. two bolts and replace element . The difficult part was removing and replacing the dishwasher...piece of cake.
Parts Used:
Dishwasher Heating Element
  • David from DEVINE, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tenant took parts with her after lease,
Just click in, you can basically do it with your eyes closed
Parts Used:
Rack Track Stop Wheel Assembly
  • Roeland from MEDINA, WA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heat dry not working. Heavy duty cycle not working.
Remove front top panel. Unplug 4 sets wires. Remove control panel with tiny wrench socket. Install new control panel. Reattach wires & replace tip front panel.
Parts Used:
CNTRL-ELEC
  • Richard from CUMMING, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
New filter
Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly
Parts Used:
Dishwasher Filter
  • John from SAINT CHARLES, MO
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper spray for bottom rack, broken
Upper jet part for top rack, directly beneath it....it has nubs meant to slide in grooves for the replacement. Waited a week for the new part, once arrived, I slipped the piece in place as nubs for my guide, and it snapped in pkace.

Easy fix.
Parts Used:
Upper Spray Arm
  • Melvin from KLAMATH FALLS, OR
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ADB1100AWB4
61 - 75 of 147
Back to Top